Simu T3.5 DC ESP Hz 12V Notice Originale page 7

EN
SIMU S.A.S. au capital de 5 000 000 € - Z.I. Les Giranaux - BP71 - 70103 ARC-LÈS-GRAY CEDEX - FRANCE - RCS VESOUL B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090
Sphere of application and liability
These instructions apply to all T3.5 DC ESP Hz drive, the different versions of which are available in the current catalogue.
Field: The T3.5 DC ESP Hz drive is designed to motorise vertical awnings (valance, screen, and projection) and horizontal
awnings (Folding arm, Cassette). It is operated using an Simu Hz controls and sensors. It would be powered by Simu battery ref
9014734, or by one another 12 V NimH battery (see characteristics chapter 1.2). The installer, who must be a motorisation and
home automation professional, must ensure that the drive product is installed in accordance with the standards in force in the
country in which it is installed such as EN 13561 relating to outdoor screens and awnings.
Liability: Before installing and using the drive, please read operating and installation guide carefully. Please read
these instructions carefully before installing and using the drive. In addition to following the instructions given in this guide,
the instructions detailed in the attached Safety instructions document must also be observed. The drive must be installed
by a motorisation and home automation professional, according to instructions from SIMU and the regulations applicable in
the country in which it is commissioned. It is prohibited to use the drive outside the field of application described above. Such
use, and any failure to comply with the instructions given in this guide and in the attached Safety instructions document,
absolves SIMU of any liability and invalidates the warranty. The installer must inform its customers of the operating and
maintenance conditions for the drive and must provide them with the instructions for use and maintenance, and the attached
Safety instructions document, after installing the drive. Any After-Sales Service operation on the drive must be performed by a
motorisation and home automation professional. If in doubt when installing the drive, or to obtain additional information, contact
a SIMU adviser or go to the website www.simu.com.
1
Installation
Instructions which must be followed by the drive and home automation professional installing the drive:
- Methods of wiring are given by national standards or IEC 60364 standard.
- Cables which pass through a metal wall must be protected and isolated using a sheath or sleeve.
- The cable for the motor cannot be removed. If it is damaged, return the drive to the After-Sales department.
Recommendations: Keep a minimum distance of 20 cm between two DC ESP Hz motors. Keep a minimum distance of 30 cm
between DC ESP Hz motors and Hz transmitters. A radio appliance using the same frequency (433,42 MHz) may deteriorate
our product's performance (ex. : hi-fi radio headphones).
- Use an antistatic fabric.
29
Ø38,2
1.1- Assembly:
PLASTITE FXS N7 \ 7X12 ZING
(5005970)
1.2- Wiring:
The wire between the motor and the power supply must not exceed 8 ft (2.5m) with AWG18 wires.
- The motor power supply line must be equipped with a quick disconnect and an over-current protection.
- Cables routed through a metal wall must be protected and insulated by sleeving or sheathing.
- Secure the cables to prevent any contact with moving parts.
T3.5 DC ESP Hz 12V
C
D
L2
L1
03/23 - 06/18 - 10/12
IP44
1
1,2
A
ØB
A
Ømin.
(mm)
(mm)
37 433 4.2
4
3
2
5113029B
EN- Original instructions
ØB C D L1 L2
(mm) (mm) (mm) (mm) (mm)
8 5.5 457 471
Ø4 x 10 / 120°
STEEL
1/6