Quick G 600 Manuel De L'utilisateur page 19

POS. DESCRIPTION
19 Idler gear
20 Bearing
21 Plug
22 Screw
23 Windlass base "G"
24 Bearing
25 Circlip
26 Output gear
27 Plug
28 Short shaft
29 Oil seal
30 "G" windlass cover
31 Assembled sensor
32 Rope/chain stripper "G"
33 Screw
34 "G" windlass clutch
35A Gypsy "G" 6 mm, integrated
rope/chain stripper 32
35B Gypsy "G" 7 mm - 1/4", integrated
rope/chain stripper 32
35C Gypsy "G" 8 mm, integrated
rope/chain stripper 32
35D Gypsy "G" 5/16", integrated
rope/chain stripper 32
36 Gypsy cover - Stainless steel
37 Windlass lever - Nylon
38 Gasket/jig "G"
39 Studs
40 Washer
41 Spring washer
42 Nut
43 Cable
44 Screw
45 Gasket watertight
46 Long shaft
47 Key
48 Drum - Stainless steel
49 Bush
50 Plug
51 Grower
52 Plug
GENIUS 600/1000/1100-F - REV008A
CODE
MSLRTZ242000
MBJHK1212000
Quick
MBSC12050A00
ant to marine environments. In any case, any salt deposits
MBV0550MXCE0
on the outside must be removed periodically to avoid cor-
SGMSC07G0000
rosion and damage to the equipment. The parts where salt
MBJ160060000
may have built up should be washed thoroughly with fresh
MBAE3415Y000
water.
MSLRTU442000
MBSC08016A00
Once a year, the drum and the gypsy are to be taken apart
MSAS07129R10
as follows:
PGPRL3047700
SGMSG07G0000
VERSION WITH FREEFALL SYSTEM
SAKREED00000
Use the handle (37) to unscrew the gypsy cover (F); loosen
MSN07GX00000
screw (H) and take off the gypsy cover. Loosen the screws
MBV0516MXCE0
(33) of the chain stripper (32) and remove it; remove the
MSF07G000000
gypsy (35).
ZSB0706G00R3
NO-DRUM VERSION
Use the handle (37) to remove the gypsy cover (36); remove
ZSB070714GR4
the top clutch cone (34); loosen the fixing screws (33) of the
chain stripper (32) and remove it and pull off the gypsy (35).
ZSB0708G00R4
ZSB070516GR4
DRUM VERSION
MSGB07GX0000
Use the handle (37) to loosen the bush (49); pull off the drum
PVLVSDN00000
(48) and the top clutch cone (34); loosen the fixing screws
PGBSG0800000
(33) of the rope/chain stripper (32) and remove it. Pull off
MBP080608X00
the gypsy (35).
MBR08X000000
MBR08XDE0000
Clean all the parts removed to avoid corrosion, and grease
MBD08MXEN000
the shaft thread (28, 46 or A) and the gypsy (35) where the
SAECC116G0L0 clutch cones rest (use grease suitable for marine environ-
ment) (34).
MBV0806MXVEP
PGCR07G00000
Remove any oxide deposits from the terminals of the elec-
MSAS07168R10
tric motor and the reversing contactor unit; grease them.
MBH0606020X0
MSE0800X0R00
MSD040000R01
MBSC04008A00
MBG05X000000
MBSC04007A00
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain from the gypsy.
® windlasses are manufactured with materials resist-
GB
19