DeWalt DWS709 Guide D'utilisation page 6

FIG. 1
DW7080
LOCKNUTS
END PLATE
DW7053
DW7082
Dust Bag: DW7053
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the
sawdust produced.
Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
SAW BLADES: ALWAYS USE 12" (305 mm) SAW BLADES WITH EITHER 1" (25.4 mm) OR
5/8" (15.88 mm) ARBOR HOLES. SPEED RATING MUST BE AT LEAST 4800 RPM. Never
use a smaller diameter blade. It will not be guarded properly. Use crosscut blades only!
Do not use blades designed for ripping, combination blades or blades with hook angles in
excess of 7°.
DW7051
BRACKET
KNOBS
DW7084
BLADE DESCRIPTIONS
APPLICATION
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose
Fine Crosscuts
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts
Non-ferrous metals
NOTE: For cutting non-ferrous metals, use only saw blades with
TCG (Triple Chip Grind) teeth designed for this purpose.
Unpacking Your Saw
Check the contents of your miter saw carton to make sure that you have received all parts.
In addition to this instruction manual, the carton should contain:
1 DWS709 miter saw
1 D WALT 12" (305 mm) diameter saw blade
E
In bag:
1 Blade wrench
1 DW7053 dustbag
1 Material clamp
Specifications
CAPACITY OF CUT
50º miter left, 60º miter right,
49º bevel left and right
0º Miter / 0º Bevel
45º Meter / 0º Bevel
50º Miter / 0º Bevel
60º Miter / 0º Bevel
45º Bevel - Left / 0º Miter
45º Bevel - Right / 0º Miter
Crown Flat (Spring Angle 38)
Crown Flat (Spring Angle 45)
NOTE: Your saw is capable of cutting the following once a special setup procedure is
followed. Refer to Special Cuts.
0º Miter / 0º Bevel
45º Meter / 0º Bevel
50º Miter / 0º Bevel
45º Meter - Left / 0º Miter
Crown Flat (Spring Angle 38)
Crown Flat (Spring Angle 45)
4
DIAMETER TEETH
12" (305 mm) 40
12" (305 mm) 60
12" (305 mm) 80
12" (305 mm) 96
HEIGHT WIDTH
4-1/2" (114 mm) 9-9/16" (243 mm)
4-1/2" (114 mm) 6-11/16" (171 mm)
4-1/2" (114 mm) 6-1/16" (155 mm)
4-1/2" (114 mm) 4-5/16" (110 mm)
2-7/16" (62 mm) 9-9/16" (243 mm)
1-11/16" (43 mm) 9-9/16" (243 mm)
2-13/16" (72 mm) 8-1/16" (206 mm)
1-1/4" (33 mm) 7-3/4" (198 mm)
HEIGHT WIDTH
2-15/16" (75 mm) 13-3/8" (340 mm)
2-1/16" (53 mm) 9-13/16" (250 mm)
2-1/16" (53 mm) 9-1/8" (232 mm)
7/8" (23 mm) 9-9/16" (354 mm)
7/8" (23 mm) 11-5/16" (288 mm)
7/8" (23 mm) 10-7/8" (276 mm)