DeWalt DWS709 Guide D'utilisation page 16

Dust Duct Cleaning
Depending on your cutting environment, saw dust can clog the dust duct and may prevent
dust from flowing away from the cutting area properly. With the saw unplugged and the saw
head raised fully, low pressure air or a large diameter dowel rod can be used to clear the dust
out of the dust duct.
Brushes
WARNING: To reduce the risk of injury, turn unit off and disconnect it from
power source before installing and removing accessories, before adjusting or when
making repairs. An accidental start-up can cause injury.
Inspect carbon brushes regularly by unplugging tool, removing the motor endcap (Fig. 4),
lifting the brush spring and withdrawing the brush assembly. Keep brushes clean and sliding
freely in their guides. Always replace a used brush in the same orientation in the holder as it
was prior to its removal. If the brushes are worn down to approximately 1/2" (12.7 mm), the
springs will no longer exert pressure and they must be replaced. Use only identical D
brushes. Use of the correct grade of brush is essential for proper operation of electric brake.
New brush assemblies are available at D
E
to "run in" (run at no load) for 10 minutes before use to seat new brushes. The electric brake
may be erratic in operation until the brushes are properly seated (worn in). Always replace the
brush inspection cap after inspection or servicing the brushes.
While "running in" DO NOT TIE, TAPE, OR OTHER WISE LOCK THE TRIGGER SWITCH ON.
HOLD BY HAND ONLY.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
E
Recommended accessories for use with your tool are available at extra cost from your
local dealer or authorized service center. If you need assistance in locating any accessory,
please contact D WALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call
E
1-800-4-D WALT (1-800-433-9258) or visit our website: www.dewalt.com.
E
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including
brush inspection and replacement) should be performed by a D
a D WALT authorized service center or other qualified service personnel. Always use identical
E
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY SERVICE: Registering your product will help you obtain more efficient
warranty service in case there is a problem with your product.
• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or
theft, your registration of ownership will serve as your proof of purchase.
WALT service centers. The tool should be allowed
WALT, have not been tested
E
WALT factory service center,
E
• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely
event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty materials or workmanship for
E
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
apply to accessories or damage caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and you may have other rights which vary
in certain states or provinces.
In addition to the warranty, D
E
WALT
E
D WALT will maintain the tool and replace worn parts caused by normal use, for free, any time
E
during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your D
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific warranty information contained in the
packaging, call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-D WALT (1-800-433-9258) for a free replacement.
E
14
WALT (1-800-433-9258). This warranty does not
E
WALT tools are covered by our:
1 YEAR FREE SERVICE
WALT Power Tool, Laser, or
E