jbc AM 6800 Guide De Référence page 3

All manuals and user guides at all-guides.com
SPECIFICATIONS
The AM 6800 is a rework station for through-hole
and SMT boards.
- AM 6800 230V
- AM 6800 120V
It contains 4 modules which cover the main rework
tasks:
- Hot air for desoldering any size of SMD
components.
The station uses the exclusive JBC system,
based on protectors-extractors and hot-air
flow, which makes desoldering clean and quick,
concentrating the heat on the IC, and protecting
the rest of the circuit at the same time.
A medium-sized SMD can be desoldered in
less than 20 seconds.
- Desoldering SMTs and cleaning of through-
hole components and pads by using the
DR 5650 desoldering iron, which contains a
self-contained vacuum pump.
- Pick & Place MP 2260 pencil by suction to aid
components positioning.
- Soldering of all types of components, with the
swift response, power and temperature
recovery of the JBC series.
Any of the JBC tools for soldering-desoldering Any of the JBC tools for soldering-desoldering
Any of the JBC tools for soldering-desoldering Any of the JBC tools for soldering-desoldering Any of the JBC tools for soldering-desoldering
can be connected to the two modules: can be connected to the two modules: can be connected to the two modules: the can be connected to the two modules: can be connected to the two modules:
soldering handpieces, the DR 5650 desoldering
iron, the AP 1300 solder feed iron and the tweezers.
The standardization of connections allows you to
adapt your configuration in the best way to your
job's needs. Do notice that you can connect only
one desoldering iron.
The station's components
- Control unit with 1000 W heater
- 2245 handpiece
with the 2245-003 cartridge
- DR 5650 desoldering iron
with the 5600-003 tip
- MP 2260 Pick & Place
Accessories for the heater:
- JT 8700 heater stand
- Extractor stand
- Set of 5 protectors.
- Set of 5 extractors.
- 2 tripods for the protectors.
- Set of 4 suction cups
- 3 nozzles:
ø 4
ø 6
ø 8
In order to make the nozzles removal easier, the
stand has a special bushing.
- Suction tube with connectors
Ref. 6800200
- Pedal with cable and connector Ref. 0964551
Ref. 6800100
Accessories for the 2245 handpiece:
- AD 8245 soldering iron stand
Accessories for the desoldering iron:
- DR 8500 desoldering iron stand Ref. 0788500
- External desoldering air filter
- Spare filters
- Set of accessories
Accessories for the Pick & Place:
- Set of suction cups Pick & Place Ref. 0940163
- Set of straight needles
- Set of bent needles
- Instructions manual
The AM 6800 station has the following
complementary products:
- 2210 handpiece
- PA 1200 micro hot tweezers
- PA 4200 hot tweezers
- AP 1300 solder feed iron
Control unit technical specifications
- Maximum power soldering iron 50W
- Maximum power desoldering iron 75W
- Power heating unit 1000W
- Temperature selection of the soldering part:
from 90 to 450°C or 190 to 840°F (±5%)
- Temperature selection hot air:
from 150 to 450°C or 300 to 850ºF (±5%)
- Air flow regulation: 6-45 l/min
- Self-contained vacuum pump for holding ICs
Ref. 2245000
- Station's maximum power: 1150W
Ref. 2245003
- ESD protected housing.
Ref. 5650000
Typical surface resistance: 10
Ref. 5600003
square
Ref. 2260000
- Complies with CE standards on electrical
safety,
Ref. 0828700
antistatic protection.
Ref. 0932845
- RoHS compliant.
- Equipotential connector and the tool tip are
connected to station mains ground supply for
ESD protection.
Ref. 0930110
- Weight of complete unit: 19.8 kg
Ref. 0932015
This product should not be thrown in the
Ref. 0932012
garbage.
Ref. 0932020
2
ENGLISH
Ref. 0932330
Ref. 0788245
Ref. 0821830
Ref. 0781046
Ref. 0780593
Ref. 0901546
Ref. 0861660
Ref. 0002791
Ref. 2210000
Ref. 1200000
Ref. 4200000
Ref. 1300000
5 -10 11
electromagnetic compatibility and
Ohms/