DeWalt DCD991 Traduction De La Notice D'instructions Originale page 39

Three‑Speed Gearing (Fig. A, C, D, E)
The three-speed feature of your tool allows you to shift gears
for greater versatility. To select speed 1 (highest torque setting),
turn the tool off and permit it to stop. Slide the speed selector
all the way forward. Speed 2 (middle torque and speed setting)
is in the middle position. Speed 3 (highest speed setting) is to
the rear.
nOTE: Do not change gears when the tool is running. Always
allow the drill to come to a complete stop before changing
gears. If you have trouble changing gears, make sure that the
speed selector is engaged in one of the three speed settings.
If the speed selector becomes stuck or is difficult to select the
desired gear, pull the variable speed trigger switch
the motor, then select the gear.
LED Worklight (Fig. A)
The LED worklight and its worklight switch
9
on the foot of the tool. The worklight is activated when the
trigger switch is depressed. The low
spotlight 20 modes can be changed by moving the switch on
the foot of the tool. If the trigger switch remains depressed, the
worklight will remain on in all modes.
When on low and medium settings, the beam will automatically
turn off 20 seconds after the trigger switch is released.
Spotlight Mode
The high setting is the spotlight mode. The spotlight will run
for 20 minutes after the trigger switch is released. Two minutes
before the spotlight will shut off, it will flash twice and then dim.
To avoid the spotlight shutting off, lightly tap the trigger switch.

WARNING: While using the worklight in medium or
spotlight mode, do not stare at the light or place the drill in
a position which may cause anyone to stare into the light.
Serious eye injury could result.

CAUTION: When using the tool as a spotlight, be sure
it is secured on a stable surface where it will not cause a
tripping or falling hazard.

CAUTION: Remove all accessories from the chuck before
using the drill as a spotlight. Personal injury or property
damage could result.
Low Battery Warning
When in spotlight mode and the battery is nearing complete
discharge, the spotlight will flash twice and then dim. After two
minutes, the battery will be completely discharged and the
drill will immediately shut down. At this point, replace with a
charged battery.

WARNING: To reduce the risk of injury, always have a
back-up battery or secondary lighting available if the
situation warrants it.
Keyless Single Sleeve Chuck (Fig. F–H)

WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
8
3 to rotate
are located
10
18 , medium 19 , and
switch and remove the battery from the tool when
changing acces sories.

WARNING: Always ensure the bit is secure before starting
the tool. A loose bit may eject from tool, causing possible
personal injury.
Your tool features a keyless chuck
sleeve for one-handed operation of the chuck. To insert a drill
7
bit or other accessory, follow these steps.
1. Turn tool off and remove the battery pack.
2. Grasp the black sleeve of the chuck with one hand and
use the other hand to secure the tool. Rotate the sleeve
anticlockwise (as viewed from the front) far enough to
accept the desired accessory.
3. Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve clockwise
with one hand while holding the tool with the other hand.
Continue to rotate the chuck sleeve until several ratchet
clicks are heard to ensure full gripping power.
nOTE: Be sure to tighten chuck with one hand on
the chuck sleeve and one hand holding the tool for
maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. I)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main
handle 15 , with the other hand on the side handle
control the twisting action of the drill.
Screwdriver Operation (Fig. C)
1. Select the desired speed/torque range using the speed
selector 8 on the top of the tool. If using the torque
adjustment collar , initially set the speed selector to
5
speed 2 or 3. This ensures effective control over the
fastener, allowing the screw to be seated correctly
and set to specification. Speed 1 will provide the same
clutching torque as speeds 2 and 3. However, for optimum
performance of the electronic clutch, speeds 2 and
3 are preferred.
nOTE: Use the lowest torque setting (1) first and increase
the number through to the highest setting (11) to seat the
fastener at the desired depth. The lower the number, the
lower the torque output.
EnGLIsH
6 with one rotating chuck
14 to
37