Nordpeis Q-27FL Manuel D'installation page 14

Technical data
Model
Power output
Nominal output
Efficiency
Weight(kg)
Width (mm)
Depth (mm)
Height (mm)
CO % @ 13% O
2
Flue gas temperature
Area of convection air
vent under insert
Area of convection air
vent over insert
Minimum distance from
convection air outlet to
ceiling
Air supply requirements
(m³/h)
Nominal load size
Refueling interval
Opening of the air vent
control
Operation
* Intermittent combustion refers to normal use of a fireplace,
i.e. new wood is inserted when the previous load has burned
down to ember.
Connector diameter Ø200 mm ext.
Type approved in accordance with:
European standard EN-13229
DIN plus
Bauart 1
15A B-VG
Test report no.
Q-27FL (N-27): RRF-29 09 2050,
Q-30FL (N-30): RRF-29 09 2051
Note! Report installation of a stove to your local
authority. The owner of the house is personally
responsible for ensuring compliance with the
mandatory safety requirements and must have
the installation approved by a qualified inspector.
Your local chimney sweep must also be informed
about the installation as this will affect the
routines for regular chimneysweeping services.
WARNING!
During operation some of the surfaces of the
inserts become extremely hot and can cause
burn injuries if touched. Be aware of the strong
heat radiated through the hatch glass. Placing
flammable material closer than the safe distance
indicated may cause a fire. Pyre lighting can
cause quick gas ignition with the risk of damage
to property and personal injury.
14
Q-27FL (N-27) Q-30FL (N-30)
6-12 kW 6-12kW
9 kW 10 kW
81% 81%
225/ D230 245/ D250
785 685
515 515
1315 1535
0,09 0,07
° °
265 C 280 C
² ²
600 cm 600 cm
² ²
600 cm 600 cm
550 500
21 21
2,2kg 2,9kg
49min 60min
50% 50%
Intermittent* Intermittent*
General
This manual contains instructions about how the
Nordpeis Q-27FL and Q-30FL must be constructed and
installed. In order for the Insert's function and safety to
be guaranteed, we recommend that the installation is
carried out by a professional. Our Nordpeis dealers can
recommend suitable technicians, information about our
dealers can be found at www.nordpeis.eu
Instructions for lighting are also supplied with the insert.
Read them carefully and keep them safe for future use.
The inserts are type approved and can be connected to
a chimney dimensioned for a flue gas temperature of
350°C, the external diameter of the connector is Ø200
mm.
Supply air from the open air should be used as
combustion air. Follow the recommendations for cross
section areas for convection air.
Structural support
Check that wooden joists have the sufficient load
capacity for the insert, chimney and construction parts
that are used when recessing. A completed installation
can usually be positioned on a normal wooden joist in a
single-family house as long as the total weight does not
exceed 400 kg.
Hearth plate
If the floor under the stove is flammable, it must be
protected by a non-flammable material e.g. natural
stone, concrete or 0.7 mm thick metal. The floor in front
of the hearth opening must be protected against any
falling embers using non-flammable material that
covers an area at least 300 mm in front and 100 mm
along each side of the hatch opening. A painted metal
or toughened glass hearth plate is available as an
accessory.
Chimney
The insert requires a draft in the chimney of at least
–12 Pa. The draft is affected both by the length and
area of the chimney, and by how well sealed it is.
To enable lighting with the hatch open, the minimum
recommended chimney length is 3.5 m and suitable
cross section area is 300 cm² (200 mm in diameter).
When connecting, via adapter (accessory), to a
chimney with a diameter of Ø150 the insert must
always be lit with the hatch closed.
Carefully check that the chimney is sealed and that
there is no leakage around soot hatches and flue
connections. Note that a flue with sharp bends and
horizontal routing reduces the draught in the chimney.
Maximum horizontal flue is 1 m, on the condition
that the vertical flue length is at least 5 m. It must be
possible to sweep the full length of the flue and the soot
hatches must be easily accessible.
GB