stayer CP125 Instructions D'emploi page 18

Adjusting the Cutting Depth (see figure C)
- Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
Loosen the clamping lever 24. For a smaller cutting depth,
pull the saw away from the base plate 12; for a larger
cutting depth, push the saw toward the base plate 12.
Adjust the desired cutting depth at the cutting-depth scale.
Tighten the clamping lever 24 again.
If the cutting depth cannot be fully adjusted after loosening
clamping lever 24, pull clamping lever 24 away from the
saw and swivel it downward. Release the clamping lever
24 again.
Repeat this procedure until the requested cutting depth
can be adjusted.
If the cutting depth cannot be sufficiently locked after
tightening clamping lever 24, pull clamping lever 24 away
from the saw and swivel it upward. Release the clamping
lever 24 again. Repeat this procedure until the cutting
depth is locked.
Adjusting the Cutting Angle
Loosen the wing bolts 6 and 26. Tilt the saw sidewards.
Adjust the desired measure on the scale 5. Tighten the
wing bolts 6 and 26 again.
Note: For bevel cuts, the cutting depth is smaller than the
setting indicated on the cutting-depth scale 25.
Cutting Marks
45 0
The 0° cutting mark 9 indicates the position of the saw
blade for right-angled cuts. The 45° cutting mark 8
indicates the position of the saw blade for 45° cuts.
For precise cuts, position the circular saw against the
workpiece as shown in the figure. It is best to carry out a
trial cut.
Starting Operation
- Observe correct mains voltage! The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine. Power
tools marked with 230 V can also be operated with
220 V.
Switching On and Off
To start the machine, first push the lock-off button for the
On/Off switch 2 and then press the On/Off switch 1 and
keep it pressed.
To switch off the machine, release the On/Off switch 1.
Note: For safety reasons, the On/Off switch 1 cannot be
locked; it must remain pressed during the entire operation.
To save energy, only switch the power tool on when using it.
Working Advice
Protect saw blades against impact and shock.
Guide the machine evenly and with light feed in the cutting
direction.
Excessive feed significantly reduces the service life of
the saw blade and can cause damage to the power tool.
45 0
ENGLISH
18
Sawing performance and cutting quality depend essentially
on the condition and the tooth form of the saw blade.
Therefore, use only sharp saw blades that are suited for
the material to be worked.
- Before any work on the machine itself, pull the
mains plug.
Sawing Wood
The correct selection of the saw blade depends on the
type and quality of the wood and whether lengthway or
crossway cuts are required.
When cutting spruce lengthways, long spiral chips are
formed.
Beech and oak dusts are especially detrimental to health.
Therefore, work only with dust extraction.
Sawing with Parallel Guide (see figure D)
The parallel guide 10 enables exact cuts along a workpiece
edge and cutting strips of the same dimension.
Loosen wing bolt 7 and slide the scale of the parallel
guide 10 through the guide in the base plate 12. Adjust the
desired cutting width as the scale setting at the respective
cutting mark 9 or 8; see Section "Cutting Marks". Tighten
wing bolt 7 again.
Sawing with Auxiliary Guide (see figure E)
For sawing large workpieces or straight edges, a board or
strip can be clamped to the workpiece as an auxiliary
guide; the base plate of the circular saw can be guided
alongside the auxiliary guide.
Repair service
Our after-sales service responds to your questions
conceming maintenance and repair ofyour product as well
as spare parts.
Exploded views and information on spare parts can also
be found under: info@grupostayer.com
Our customer consultants answer your questions
conceming best buy, application and adjustment of
productsand accessories.
Warranty
Warranty card
lncluded in the documentation that accompanies this
equipment, you should find the warranty card. You should
fill out the card completely and retum to vendar with a copy
of purchasing receipt or invoice and you should receive a
receipt.
Note: lf you cannot find the warranty card within
the documentation,youmust ask for it through your
supplier.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed or manipulated or
repaired otherthan themanufacturer.
Environment
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
OnlyforEC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2012/19/
UE for Waste Electrical and Electronic
Equipment and its implementation into national
right,power tools that are no longer usable
must be collected separately and disposed of
in an environmentally correct manner.
Subject to change wlthout notlce.
18