Panasonic CF-30 Serie Mode D'emploi page 2

Read Me First
Models for U.S.A.
Federal Communications Commission Radio Fre-
quency Interference Statement
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
Consult the Panasonic Service Center or an experi-
enced radio/TV technician for help.
Warning
To assure continued compliance, use only shielded inter-
face cables when connecting to a computer or peripheral.
Also, any changes or modi cations not expressly ap-
proved by the party responsible for compliance could void
the user's authority to operate this equipment.
FCC RF Exposure Warning:
This computer is provided with PC Card slot that could
be used with wireless transmitter(s), which will be spe-
ci cally recommended when they become available.
Other third-party wireless transmitter(s) have not been
RF exposure evaluated for use with this computer and
may not comply with FCC RF exposure requirements.
This computer complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
This computer may not be co-located or operated with
any other antenna or transmitter.
<For computer with installed WLAN>
This PC with WLAN transmitters installed, has been
approved for mobile operation and to assure compli-
ance with RF exposure requirements, a minimum of
20 cm (8 inches) must be maintained between the
WLAN antenna located in top of LCD and all person's
body (excluding extremities of hands, wrist and feet)
during wireless modes of operation.
<For computer with installed WWAN>
This PC with WWAN transmitter installed, has been
approved for mobile operation and to assure compli-
ance with RF exposure requirements, a minimum of
20 cm (8 inches) must be maintained between the
WWAN antenna located in top of LCD and all person's
body (excluding extremities of hands, wrist and feet)
during wireless modes of operation.
<Optional Car Mounter / Port Replicator>
This equipment is provided with external antenna
connector(s) for connection to optional Car Mount-
er or Port Replicator for mobile external mounted
antenna(s). External antenna(s) must be profession-
ally installed and cannot exceed recommended maxi-
mum antenna gain as described in individual provided
supplement instructions for wireless transmitters. Also,
user must maintain minimum 20 cm spacing between
external antenna(s) and all person's body (excluding
extremities of hands, wrist and feet) during wireless
modes of operation.
2
All manuals and user guides at all-guides.com
<Only for model with wireless LAN>
This product is restricted to indoor use due to its opera-
tion in the 5.15 to 5.25 GHz frequency range. FCC re-
quires this product to be used indoors for the frequency
range 5.15 to 5.25 GHz to reduce the potential for harm-
ful interference to co-channel Mobile Satellite systems.
High power radars are allocated as primary users of the
5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These
radar stations can cause interference with and/or damage
this product.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
Responsible Party: Panasonic Corporation of North America
FCC Regulation Notice for modem
This equipment contains a FCC approved modem.
1. This equipment complies with CFR47 Part 68 rules.
2. An FCC compliant telephone cord and modular plug
3. The REN is used to determine the quantity of devices
4. If your telephone equipment cause harm to the tele-
5. The telephone company may take changes in its facili-
including interference that may cause undesired op-
eration.
One Panasonic Way
Secaucus, NJ 07094
Tel No:1-800-LAPTOP5 (1-800-527-8675)
On the computer is a label that contains, among other
information, the FCC registration number and ringer
equivalence number (REN) for this equipment. If re-
quired, this information must be provided to the tele-
phone company.
is provided with this equipment. This equipment is
designed to be connected to the telephone network
or premises wiring using a compatible modular jack
which is Part 68 compliant. See Installation Instruc-
tions for details.
which may be connected to the telephone line. Ex-
cessive RENs on the telephone line may result in the
devices not ringing in response to an incoming call. In
most, but not all area, the sum of RENs should not ex-
ceed  ve (5.0). To be certain of the number of devices
that may be connected to a line, as determined by the
total RENs, contact the local telephone company.
phone network, the telephone company will notify you
in advice that temporary discontinuance of service
may be required. But if advice notice isn't practical, the
telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to
 le a complaint with the FCC if you believe it is neces-
sary.
ties, equipment, operations or procedures that could
affect the operation of the equipment. If this happens
the telephone company will provide advance notice
in order for you to make necessary modi cations to
maintain uninterrupted service.
English
25-M-W-1
6-M-1