Health Advice - Evolution R185 SMS Notice Originale

4) General Power Tool Safety Warnings
(2.5)
[Power tool use and care].
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at a rate
for which it was designed.
b) Do not use the power tool if the switch does
not turn it on or off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the power tool from the
power source and/or battery pack from the
power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventative safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these Instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of moving parts and any other
condition that may affect the power tools
operation. If damaged, have the power tool
repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the
tool in unexpected situations.
5) General Power Tool Safety Warnings
(2.6)
[Service] a) Have your power tool serviced by
a qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained. If the
supply cord of this power tool is damaged, it must
be replaced by a specially prepared supply cord
available through the service organization.
www.evolutionpowertools.com

HEALTH ADVICE

(2.7)
WARNING: If you suspect that paint on surfaces
in your home contains lead seek professional
advice. Lead based paints should only be
removed by a professional and you should not
attempt to remove it yourself.
Once the dust has been deposited on surfaces,
hand to mouth contact can result in the ingestion
of lead. Exposure to even low levels of lead can
cause irreversible brain and nervous system
damage. The young and unborn children are
particularly vulnerable.
WARNING: Some wood and wood type
(2.8)
products, especially MDF (Medium Density
Fibreboard), can produce dust that may be
hazardous to your health. We recommend the
use of an approved face mask with replaceable
filters when using this machine, in addition to
using the dust extraction facility.
MITRE SAW SPECIFIC SAFETY
(3.5)
• Not to use saw blades manufactured from
high speed steel.
• Use only the saw with guards in good
working order and properly maintained, and
in position.
• Always to clamp work-pieces to the saw table.
a) Mitre saws are intended to cut wood or
wood-like products, they cannot be used
with abrasive cut-off wheels for cutting ferrous
material such as bars, rods, studs,etc. Abrasive
dust causes moving parts such as the lower guard
to jam. Sparks from abrasive cutting will burn the
lower guard, the kerf insert and other plastic parts.
b) Use clamps to support the workpiece
whenever possible. If supporting the
workpiece by hand, you must always keep your
hand at least 150mm from either side of the
saw blade. Do not use this saw to cut pieces
that are too small to be securely clamped or
held by hand. If your hand is placed too close to
the saw blade, there is an increased risk of injury
from blade contact.
c) The workpiece must be stationary and
clamped or held against both the fence and
the table. Do not feed the workpiece into the
blade or cut "freehand" in any way. Unrestrained
or moving workpieces could be thrown at high
speeds, causing injury.
8