Publicité
Stage 8, the foresail winch
Part
Description
No.
8.1
Support rail
8.2
Bridge piece
8.3
Foresail winch
8.4
Screw plate
8.5
Self-tapping screw
8.6
Support block
8.7
Tongue
8.8
Self-tapping screw
8.9
Reinforcement
8.10
Tension rail
8.11
Pulley block
8.12
Ring-screw
8.13
Stop-strip
8.14
Self-tapping screw
8.15
Winch drum
-
The mountings for the foresail winch are assembled outsi-
de the model - Fig. 99, page 26.
-
File a notch in the centre of the support rail 8.1 as shown.
-
Glue the bridge piece 8.2 to it leaving a slot into which the
winch 8.3 can be pushed.
-
Fix the screw plate 8.4 to the cable end of the winch using
the screws 8.5.
-
Glue the blocks 8.6 to the tongues 8.7. Screw the assem-
bly 8.6 / 8.7 to the screw plate 8.4 using the screws 8.8.
-
Glue the reinforcements 8.9 to the spruce tension rail 8.10.
Drive in the screw 8.8 to a depth of about 3 mm.
-
Drill out the pulley block 8.11 to 2 mm Ø (Fig. 100). Open
Stage 9, the sheet guide system
Part
Description
No.
9.1
Guide tube
9.2
Support rail
9.3
Guide tube
9.4
Sleeve
9.5
Swivel
9.6
Pulley block
9.7
Sheet bar
9.8
Sheet bar
9.9
Washer
9.10
Spacer sleeve
9.11
Split pin
9.12
Return pulley block
9.13
Tubular rivet
9.14
Double block
9.15
Split pin
9.16
Tubular rivet
9.17
Jib sheet
9.18
Crimp sleeve
9.19
Rubber cord
9.20
Retaining sleeve
9.21
Schooner sheet
9.22
Swivel hook
9.23
Main sheet
9.24
Endless sheet
9.25
Crimp sleeve
9.26
Swivel hook
All manuals and user guides at all-guides.com
Assembly instructions
Valdivia
Material
Spruce
Plywood, ready made
Plywood, ready made
Steel
Spruce
Plywood, ready made
Steel
Plywood, ready made
Spruce
Brass
Brass
Spruce
Steel
Plastic
-
-
-
Material
Plastic
Spruce
Plastic
Brass rivet
Brass
Brass
Brass rod
Brass rod
Brass
Brass
Brass
Brass
Brass
Brass
Brass
Brass
Beige thread
Brass
Rubber
Brass
Beige thread
Brass
Beige thread
Beige thread
Brass rivet
Brass
10
Dimensions
No.
off
10 x 10 x 58
1
2 x 21 x 58
1
1
3 x 21 x 50
1
2.9 x 9.5
2
10 x 15 x 30
2
3 x 10 x 42
2
2.2 x 9.5
3
3 x 7 x 15
2
2 x 7 x 200
1
6 x 11.5
1
3 x 1.8 x 8
1
2 x 7 x 12
1
2.2 x 6.5
2
38 Ø
1
up the ring-screw 8.12 and fit the block on it.
Close the loop of the ring-screw again and screw it into the
reinforcement on the tension rail.
Place the tension rail on the screw plate and drill the holes
as shown in Fig. 99. Establish the position of the stop-strip
8.13 and glue the strip in place. The tension rail can now
be attached to the screw plate using the screws 8.14.
Fit the winch drum 8.15 on the sailwinch. Place the winch
assembly on the underside of the deck and position the
drum in the centre of the hatch opening. In this position
glue the support rail and the blocks in place. The tension
rail 8.10 must not be glued to the deck girder 5.1 - Fig.
101.
Dimensions
No.
off
3 Ø x 300
1
10 x 10 x 20
1
3 Ø x 150
2
3 Ø x 17
5
1
6 x 11.5
1
1.5 Ø x 140
1
1.5 Ø x 160
1
1.5 x 3.5
2
2.5 x 5
4
1.5 x 1.5 x 25
6
6 x 11.5
2
2.5 x 5
6
5 Ø
1
1 x 1.4 x 15
1
1.5 Ø x 10
1
0.4 Ø x 1.2 m
1
2.5 x 3
4
1.5 x 0.5 m
1
2.5 x 8
1
0.7 Ø x 0.85 m
1
20 long
2
0.7 Ø x 1.8 m
1
0.7 Ø x 2.0 m
1
2.5 x 3
2
14 long
2
Order No.
1140
Note
Sheet E, FS
N.I.
Sheet C
FS
Sheet C
FS
Sheet C
FS
FS
FS
With 8.3
Note
FS
FS
FS
Schooner sail
Foresails
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
Foresails
FS
FS
Publicité
