Güde HPC 150 M Mode D'emploi page 58

Pouring the Engine Oil into Gearbox (Fig. 6)
Never try to start the apparatus if there is not
enough corresponding oil in the engine. There is
no oil in the apparatus at delivery thereof. If the
apparatus operates without (sufficient quantity of)
engine oil, the engine will get damaged. Place
the apparatus on flat surface and remove the
cover from the oil tank. Fill the engine oil at least
up to the half of the measuring bar length.
Pouring the Petrol into the Tank
High-pressure cleaner is driven by a 4-stroke
engine requiring leadless petrol. Use suitable
funnel for filling up the petrol. Make sure there is
not too much petrol in the tank and prevent
spraying the petrol out. The oil should reach up to
the fuel filter, not higher.
Connection of High-Pressure Hose to the
Handle of the Gun and the Pump
Put the water pipe on the spray gun. Hold the
end of the gun and screw the pipe on it so that
the connection is firm and sure. Caution! Do not
tighten the screw too much, both supply
connections may be damaged.
The supply connection of the high-pressure hose
with the supply connection on the bottom side of
the spray gun handle connect firmly and safely.
Caution! Do not tighten the screw too much, both
supply connections may be damaged.
Safety Stop for High-Pressure Water Pipe
The gun handle has a safety device preventing
unwanted activation of high-pressure pipe. This
device can be put into operation by leasing the
handle and activating safety stop between the
trigger and the handle.
Connection of the Hose (Fig. 10)
The water supply connection is furnished with
particle filter. Never let the apparatus work
without filter. The intervals for checking and
cleaning of the filters depend on the water
quality. If the water in the water mains contains
impurity articles, the filter shall be cleaned after
every use because otherwise the apparatus
output will (considerably) fall and the pump may
be damaged.
The supply connection part for water supply has
a form of a (male) plug and shall be fastened with
screw on the inlet to water tank of the apparatus.
Put the clamping element (female) to the hose
and then connect this element with the part of
supply connection in form of a plug. Connect the
high-pressure hose to the connection/discharge
for high-pressure. Release water and press the
handle in form of a gun till the water starts flowing
from the pipe continuously.
temperature shall not exceed 40
All manuals and user guides at all-guides.com
The water
0
C..
58
Important warning: The high-pressure jet can
damage the lining, coating and pavement due
to the type of material or insufficient know-
how. Therefore check first the effect on a
smaller area. If necessary the water pressure
can be changed by replacement of the jet or
by reduction of the engine output.
Cleaning Means (Fig. 18)
Use suitable tank
determined for pressure washing machines. Do
not use rinsing means for washing, they contain
salt. Quality cleaning means for pressure
washing machines are recommended for this
high-pressure cleaner. Observe the instructions
on the vessel/canister. Most washing means for
cars contain combination of washing means and
wax for chassis (wax-washing means mixture).
They are mostly dense, viscous means. The
viscosity (hence liquid density) of the cleaning
means usually increases in cold weather. We
recommend to solve this kind of washing means
in hot water before pouring it into the vessel. At
combination of washing and wax means it is
recommended to prepare a solution before use.
As basic principle the ratio of the mixture 50:50 is
recommended. Of course, you can create a
mixture with a different ration based on testing,
that may be more suitable for your purposes.
Instructions:
•
Dense cleaning means cannot flow
properly from the cleaning vessel and
it can clog the system with deposits.
•
The cleaning vessel shall be
thoroughly rinsed with water after
use.
When using the delivered cleaning means the
black jet (low pressure) shall be fixed on the end
of the water pipe. Insert the end of the suction
pipe into the cleaning means vessel of the high-
pressure cleaner. Suction and mixing of the
cleaning means will pass automatically if the
water flows through the pump.
Installation of High-Pressure Cleaner
•
Place the high-pressure cleaner on solid
and even surface in a way enabling
properly lubrication of the engine and the
pump. When installing avoid the places
with depressions or holes (e.g. places
with puddles). When the surfaces are
smooth and slippery, there is danger of
injury!
•
Place the apparatus on a well ventilated
place in sufficiently safe distance from
inflammable materials or vapours. Safety
regulations for proper ventilation shall be
principally observed. Minimum distance
from inflammable materials shall be 50
cm.
•
The apparatus shall be placed so that the
operator will have easy access to all
with cleaning means