Bosch Kiox BUI330 Notice D'utilisation D'origine page 8

English – 4
eBike is switched on, then the on-board computer's internal
battery is powered and charged by the eBike battery.
If the on-board computer is removed from the holder (5),
the power is supplied by the on-board computer's internal
battery. If the charge of the on-board computer's internal
battery is running low, a warning message appears on the
display.
To charge the on-board computer's internal battery, slide the
on-board computer back onto the holder (5). Note that if
you do not charge the eBike battery straight away, the eBike
will automatically switch off after ten minutes of inactivity. If
this happens, the on-board computer's internal battery will
also stop charging.
You can also charge the on-board computer via the USB
port (6). To do this, open the protective cap (17). Use a Mi-
cro USB cable to connect the USB port on the on-board com-
puter to a commercially available USB charger (not included
with the product as standard) or to the USB port of a com-
puter (max. 5 V charging voltage; max. 1000 mA charging
current).
If the on-board computer is removed from the holder (5), all
values for the functions are saved and can still be scrolled
through.
After use, the USB port must be carefully resealed with the
protective cap (17).
If the on-board computer's internal battery is not recharged,
the date and time will be retained for up to six months. When
the on-board computer is switched on again, the date and
time will be reset if a Bluetooth® connection to the app has
been established and the smartphone has successfully iden-
tified the current location via GPS.
Note: The Kiox only charges while it is switched on.
Note: If the Kiox is switched off during charging via a USB
cable, the Kiox can only be switched on again once the USB
cable has been disconnected.
Note: To maximise the service life of the on-board com-
puter's internal battery, it should be recharged for one hour
every three months.
Battery charge indicator of the eBike battery
The battery charge indicator of the eBike battery d (see
"Start page", page English – 7) can be read on the status
page and in the statusbar. The eBike battery's state of
charge is also indicated by the LEDs on the eBike battery it-
self.
Colour of the indicator
Green
Orange
Red
Red + !
1 270 020 XBK | (29.05.2023)
Meaning
The eBike battery is over
30 % charged.
The eBike battery is between
15 % and 30 % charged.
The eBike battery is between
0 % and 15 % charged.
The capacity for assisting the
drive has been used up, and
assistance is switched off.
The remaining capacity will
Colour of the indicator
If the eBike battery is being charged on the bike, a corres-
ponding notification will be displayed.
If the on-board computer is removed from the holder (5),
the state of charge that was last displayed for the eBike bat-
tery is saved.
Resetting Storage Mode/Kiox
The on-board computer has an energy-saving storage mode
which minimises the rate at which the internal battery dis-
charges. Setting to this mode erases the date and time.
This mode can only be activated by pressing and holding the
on/off button (4) of the on-board computer for at least
eight seconds.
If the on-board computer does not start when the on/off but-
ton (4) is pressed briefly, the on-board computer is in stor-
age mode.
You can deactivate storage mode by pressing the on/off but-
ton (4) for at least two seconds.
The on-board computer detects whether it is in a fully func-
tional condition. If you press and hold the on/off button (4)
for at least eight seconds while in a fully functional condition,
the on-board computer will go into storage mode. If, con-
trary to expectations, the Kiox is not in a fully functional con-
dition and cannot be operated, pressing and holding the on/
off button (4) (for at least eight seconds) will reset it. After
being reset, the on-board computer will restart automatically
after approx. five seconds. If the Kiox does not restart, press
the on/off button (4) for two seconds.
To reset the Kiox to its factory settings, select <Set-
tings> → <Sys settings> → <Factory reset>. All user data
will be lost.
Setting the assistance level
On the operating unit (7), you can set the level of assistance
you want the eBike drive to provide you with while pedalling.
The assistance level can be changed at any time, even while
cycling.
Note: In some models, the assistance level may be preset
and cannot be changed. There may also be fewer assistance
levels available than stated here.
The following assistance levels are available as a maximum:
– OFF: Drive assistance is switched off. The eBike can only
be moved by pedalling, as with a normal bicycle. The walk
assistance cannot be activated at this assistance level.
– ECO: Effective assistance with maximum efficiency, for
maximum range
– TOUR/TOUR+:
TOUR: Steady assistance, long range for touring
TOUR+: Dynamic assistance for natural, sporty cycling
(only in conjunction with eMTB)
Meaning
be provided for the bike
lights and the on-board com-
puter.
Bosch eBike Systems