Xylem Rule iL500Plus Mode D'emploi page 2

Submersible Inline Pumps
Features
• Pumps fresh and sea water.
• Rapid diesel refueling and transfer with no spillage (models iL500Plus, iL280Plus,
iL200Plus and iL120Plus only).
• Bilge pump-out in tight areas.
• Water transfer; deck showers; deck,anchor & general wash-down.
• Robust, slim line with clip-on easily cleaned filter.
Instructions
Fit a length of appropriate size hose (see specification table for details) to the outlet nozzle and
immerse the complete pump in liquid. Connect the battery clips to the battery terminals (+) positive
to (+) positive and (—) negative to (—) negative (if powering from a car or boat battery do not use
with engine running). The pump will deliver immediately.
For an in-line installation unclip the filter to expose the inlet nozzle. Connect a length of hose
between the tank and nozzle. The pump must be fitted below the tank.
• Avoid dry running for long periods.
• For drinking water applications sterilize regularly.
• Store away from excessive heat and direct sunlight to avoid external damage.
• If the pump fails to perform, check for blockages (including filter), leaks and correct hose &
electrical connections.
WARNING: DO NOT use any Rule pump for petrol, petroleum products or any products
with a flash point below 37°C (98°F).
Specifications
Model
Part No.
Pump Type
Current
Head
Flow rate
Rating
Outlets
(ID hose)
Pressure
Body
Length 6.5" (165mm)
Diameter
Cable Length
Weight 1.1 lbs (500g)
Liquid
Operating
Temp.
* Continuous Duty — Should not be run dry for long periods of time.
^ Intermittent Duty — Should not be run for more than 20 mins. and rested for equal time.
Warranty: All products of the company are sold, and all services of the company are offered subject to the
company's warranty and terms of sale, copies of which will be furnished upon request. Details correct at time of
printing. We reserve the right to change specifications without prior notice.
iL500 iL280
Plus
iL500P
iL500P-24 iL280P-24
12V (6 amp) 12V (4.5 amp)
24V (3 amp) 24V (2.5 amp)
32 ft (9.7m) 32 ft (9.7m)
500 GPH 280 GPH
(1920 LPH) (1080 LPH)
Continuous* Continuous*
3/4" (19mm) 1/2" (13mm)
14 PSI
(0.96 bar) (0.96 bar)
POM
6.5" (165mm)
1.5" (38mm) 1.5" (38mm)
13 ft (4m) 13 ft (4m)
1.1 lbs (500g)
Fresh & Sea Water / Diesel
iL200
Plus
iL280P iL200P
iL200P-24
Centrifugal, submersible, in-line pump
12V (4.5 amp)
24V (2.5 amp)
32 ft (9.7m)
200 GPH
(760 LPH)
Continuous*
1/2" (13mm)
14 PSI 11 PSI
(0.76 bar)
POM POM
6.5" (165mm)
1.5" (38mm)
3 ft (1m)
0.5 lbs (227g)
Water to 176°F (80°C)
Diesel to 104°F (40°C)
iL120
Plus Plus
iL120P
12V (1 amp)
9 ft (2.7m)
120 GPH
(454 LPH)
Continuous
1/2" (13mm)
9 PSI
(0.62 bar)
POM
6.5" (165mm)
1.5" (38mm)
3 ft (1m)
1.1 lbs (500g)
iL200
iL200
12V (2.8 amp)
25 ft (7.6m)
200 GPH
(760 LPH)
Intermittent^
3/8" (10mm)
1/2" (13mm)
14 PSI
(0.96 bar)
HIP
5.1" (130mm)
1.4" (36mm)
3 ft (1m)
0.25 lbs (113g)
Fresh & Sea
Water
Water to 140°F
(60°C)