Royal Catering RCEC-3000-E Manuel D'utilisation page 5

This device is intended for preparation of pancakes. The surface of the plates is non-
stick coated and can therefore easily be cleaned. This unit is only intended for use of
this kind and not for preparation of other meals.
SAFETY GUIDELINES
1. Please read and understand these instructions carefully before operating the
device! Please observe the safety guidelines carefully in order to prevent damages
through improper use!
2. Please keep this manual available for future reference. If this device will be passed
to third parties, the manual must be passed too.
3. Only use this device for the intended use and indoors only.
4. The crepe maker is only intended for preparing meals.
5. We do not offer any warranty for damages because of improper use or incorrect
operation.
6. Check before first use, whether mains voltage type of current comply with the
indicated data on the type plate.
7. This device is not intended to be used by persons (including children) with
limited physical, sensory or mental aptitude or lack of experience and/or know-
ledge unless they are supervised by a person responsible for their safety or have
received instruction from this person as to how the device is used.
8. ELECTRICAL SHOCK HAZARD! Do not attempt to repair the unit yourself. In
case of failures of the device, repair must be made by qualified experts.
9. Please check mains plug and power cable regularly. If the power cable for this
device is damaged, it has to be replaced by the manufacturer or its customer
service or another qualified person, in order to prevent hazards.
10. Prevent damages of the power cable through squeezing, bending on sharp edges
and keep it away from hot surfaces and open flames.
11. ATTENTION DANGER TO LIFE! While cleaning never immerse the device in
water or other liquids.
12. Under no circumstances open the housing.
A. TECHNICAL DATA
Model Voltage (V) Frequency (Hz) Power (kW)
RCEC-3000-E 230 50
RCEC-6000-E 230 50
RCEC-3000-R 230 50
8
Dimension (mm)
3 450*485*220
2x3 860*500*220
3 400*400*160
Rev. 30.03.2017
B. SERVICE ENVIRONMENT
Temperature of environment cannot be higher than 50°C.
Keep the device away from hot surfaces. Operate the device on flat, stable, clean,
refractory and dry surface out of the reach of children and mentally disabled persons.
Install the device, so that the main plug is always accessible.
C. INSTALLATION
1. The installation and maintenance should be done by professional technicians
2. The operating voltage of this equipment must be coordinated with the supplied
voltage.
3. Do not put it close to inflammable objects in case of accidental fire.
ATTENTION: The crepe maker is getting very hot, when the device heats up. Dan-
ger of burnings! Keep children away
4. Connect power, green indicator is on, turn thermostat to the setting tempera-
ture, green indicator is still on, yellow indicator is on as well. Equipment starts to
heat, when temperature goes up to the setting temperature, thermostat cuts off
heating power automatically with green indicator is still on but yellow indicator
is off. When temperature lowers down to certain temperature data, thermostat
restarts to connect heating power again, at this time, both green indicator and
yellow indicator are on, equipment is being heated.
NOTE: Use only tools of heat resistant plastic or wood, to avoid damages of the anti-
sticking coating of the crepe maker. Make sure the tools have sharp edges.
5. After use, please turn the device off with the on-/off switch and pull out the main
plug off the socket. Let the device cool down at a place out of the reach of child-
ren. After cool-down, please clean the device according to the section „cleaning
and maintenance".
D. TRANSPORTATION AND STORAGE
In transportation use should prevent it from being shaked vidently,
crashed and put upside down. Put it in a ventilated warehouse and maintenance that
is with dry air but without any corrosive gas.
E. CLEANING AND MAINTENANCE
1. Cut off electricity when cleaning equipment.
2. Use cleaner without corrosive to clean surface.
3. Dry all parts well after cleaning, before the device is used again.
4. Store the unit in a dry, cool location, free from moisture and direct exposure of
sunlight.
Rev. 30.03.2017 9