Publicité
Les langues disponibles
Les langues disponibles
Ch 1
Ch 2
500
Lux
Pulse
2min
5min
10min
8
Ch 1
15min
30min
60min
Hours
The detection area is tested by activating the integrated motion sensor for the
Test
Short
Long
Fact.
Pulse
On/Off
push
push
walking test:
setting
Lock/
- Press
unlock
15min
- The green indication LED flashes twice to confirm. The device is now in 'set' mode.
20
Test
- Press
Lux
On/Off
- Both channels are activated.
300
- The blue indication LED lights up when you activate the test mode and no
Lux
movement is detected by the sensor.
- Lighting is switched on for five seconds and the red indication LED lights up each
500
Lux
time the sensor detects activity.
- If no activity is detected and the sensor is still in test mode, the blue indication LED
Ch 1
lights up.
- Complete the walking test by pressing
Pulse
- Lock the device by pressing
- If you forget to close the test mode, the detector will return to the selected settings
15min
after five minutes.
Test
On/Off
The light sensor does not work during the walking test.
You can also activate the walking test via the potentiometer for the switch-off delay.
4.2. 'Set' buttons
To change the settings of the detector:
Lock/
Light 1
Light 2
LED
1. Press
three times within five seconds to unlock the device.
unlock
On/Off
On/Off
On/Off
The green indication LED flashes twice to confirm. The device is now in 'set' mode.
20
50
100
200
Lux
Lux
Lux
Lux
2. Change the light level or the switch-off delay using the buttons below.
300
400
Learn actual lux
Lux
Lux
Lock/
Light 1
Light 2
LED
3. Press
once to lock the device again.
unlock
On/Off
On/Off
On/Off
Lock/
Light 1
Light 2
LED
500
700
1000
No
unlock
On/Off
On/Off
On/Off
Lux
Lux
Lux
Lux
The green indication LED flashes twice to confirm. The modified setting is activated and the device will return
20
50
100
200
Lux
Lux
Lux
Lux
to the selected settings.
20
50
100
200
Status
Status
Ch 1
Ch 2
Lux
Lux
Lux
Lux
Ch 1
Ch 2
Lock/
Light 1
Light 2
LED
300
400
Learn actual lux
unlock
On/Off
On/Off
On/Off
Lux
Lux
Note: If you do not lock the device, it will be locked automatically after two minutes. All changes will then be
300
400
Learn actual lux
Pulse
2min
5min
10min
Lux
Lux
saved automatically.
20
50
100
200
500
700
1000
No
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
500
700
1000
No
8
Button
Function
15min
30min
60min
Lux
Lux
Lux
Lux
Hours
300
400
Status
Status
Learn actual lux
Ch 1
Ch 2
Lux
Lux
Ch 1
Ch 2
Press this button to set the lux value and/or the switch-off delay
Test
Status
Short
Status
Long
Fact.
Ch 1
Ch 2
On/Off
push
Ch 1
Ch 2
push
setting
for channel 1.
500
700
1000
No
Pulse
2min
5min
10min
Lux
Lux
Lux
Lux
The red indication LED indicates that you can adjust the setting.
Pulse
2min
5min
10min
Press this button to set the lux value and/or the switch-off delay
Status
Status
8
Ch 1
Ch 2
15min
30min
60min
Ch 1
Ch 2
Lock/
Light 1
Light 2
LED
Hours
for channel 2.
Lock/
Lock/
Light 1
Light 1
Light 2
Light 2
LED
LED
unlock
On/Off
On/Off
On/Off
Lock/
Light 1
Light 2
LED
8
unlock
unlock
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
15min
30min
60min
unlock
On/Off
On/Off
On/Off
Hours
The blue indication LED indicates that you can adjust the setting.
Test
Short
Long
Fact.
Pulse
2min
5min
10min
20
On/Off
50
push
100
push
200
setting
- With these red buttons, you set the desired light level (lux value).
20
20
50
50
100
100
200
200
Lux
Lux
Lux
Lux
Test
20
Short
50
Long
100
Fact.
200
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
On/Off
Lux
push
Lux
push
Lux
setting
Lux
- There are ten fixed lux values: 20, 50, 100, 200, 300, 400, 500, 700
8
15min
30min
60min
Hours
and 1000 lux and No lux (daylight-independent).
300
400
Lock/
Light 1
Light 2
LED
Learn actual lux
300
300
400
400
Lux
Lux
unlock
On/Off
On/Off
Learn actual lux
Learn actual lux
On/Off
300
400
Lux
Lux
Lux
Lux
Learn actual lux
Lux
Lux
Test
Short
Long
Fact.
On/Off
push
push
setting
500
700
1000
No
20
50
100
200
500
500
700
700
1000
1000
No
No
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lock/
500
Light 1
700
Light 2
1000
LED
No
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
unlock
Lux
On/Off
Lux
On/Off
Lux
On/Off
Lux
- With this button, you set the current light level in the room as the desired
Status
Status
300
400
Ch 1
Ch 2
Learn actual lux
Status
Status
Status
Status
Ch 1
Ch 2
Lux
Ch 1
Ch 1
Ch 2
Ch 2
Lux
20
50
Status
100
Status
200
level at which the lighting should be switched on.
Ch 1
Ch 1
Ch 2
Ch 2
Ch 1
Ch 2
Lux
Lux
Lux
Lux
Ch 1
Ch 2
- If you press this button, the red indication LED will flash once to indicate that
500
700
1000
No
Pulse
2min
5min
10min
the current light level is being saved. If this light level is not between 20 and
Lux
Pulse
Pulse
Lux
2min
2min
Lux
5min
5min
Lux
10min
10min
300
400
Lock/
Pulse
2min
Learn actual lux
5min
10min
Light 1
Light 2
LED
1
Light 2
LED
Lux
Lux
unlock
On/Off
On/Off
On/Off
ff
On/Off
On/Off
1000 lux, the minimum level (20 lux) or maximum level (1000 lux) will be saved.
8
Status
Status
15min
30min
60min
Ch 1
Ch 2
8
8
Hours
15min
15min
30min
30min
Ch 1
60min
60min
Ch 2
500
700
1000
No
8
Hours
Hours
15min
20
30min
50
60min
100
200
100
200
Lux
Lux
Lux
Hours
Lux
Lux
Lux
Lux
Lux
Use this setting if the desired minimum light level in the room has been achieved.
Lux
Lux
Test
Short
Long
Fact.
This is the point at which the lighting should be switched on as the daylight
Pulse
2min
Test
Test
Short
Short
5min
10min
Long
Long
Fact.
Fact.
On/Off
push
push
setting
Test
Short
Long
Fact.
Status
Status
On/Off
On/Off
push
push
push
push
setting
setting
Ch 1
300
Ch 2
400
On/Off
400
push
push
setting
Learn actual lux
Ch 1
Ch 2
level is no longer sufficient.
rn actual lux
Lux
Lux
Lux
8
- With these blue buttons, you set the desired switch-off delay.
15min
30min
60min
1
Light 2
LED
Hours
Pulse
2min
5min
10min
ff
On/Off
On/Off
500
700
1000
No
1000
No
- There are six fixed values: 2, 5, 10, 15, 30 and 60 minutes.
Lux
Lux
Lux
Lux
Lux
Lux
Test
Short
Long
Fact.
On/Off
100
push
200
push
setting
8
Lux
15min
Lux
30min
Status
60min
Status
Status
Status
Hours
Ch 1
Ch 2
Ch 1
Ch 2
Ch 1
Ch 2
Not applicable.
400
Test
Short
Long
Fact.
rn actual lux
Lux
On/Off
push
push
setting
Pulse
2min
5min
10min
n
5min
10min
1000
No
Press this button:
Lux
Lux
8
15min
8
30min
60min
n
60min
Hours
Hours
- The selected channel will be switched on permanently for eight hours.
This time can, for example, be used to set HVAC installations connected to
Status
Status
Test
Short
Long
Fact.
Ch 1
Ch 2
t
Long
Fact.
On/Off
push
push
setting
this channel.
push
setting
- The blue indication LED will flash (0.25 s on and 2 s off).
5min
10min
Press this button again to deactivate the function. The blue indication LED
8
n
60min
Hours
will no longer flash. You cannot switch off this function via a push button.
The device returns to the factory settings.
t
Long
Fact.
push
setting
5. OPERATION AND USE
5.1. Activation
The detector should not be powered until all cables are connected. After powering the device, the detector will be
ready for use after approximately 120 seconds (warm-up time).
The red indication LED flashes during warm-up time. After the device has warmed up, the green indication LED
will flash briefly twice.
PM350-20072R17192
700
1000
No
Lux
Lux
Lux
All manuals and user guides at all-guides.com
Lock/
Light 1
Light 2
unlock
On/Off
On/Off
Status
Status
Ch 2
Ch 1
Ch 2
20
50
100
Lux
Lux
Lux
2min
5min
10min
300
Learn actual lux
Lux
Light 1
Light 2
LED
three times within five seconds to unlock the device.
8
On/Off
On/Off
On/Off
30min
60min
Hours
500
700
1000
Lux
Lux
Lux
50
100
200
Short
Long
Fact.
Lux
Lux
Lux
push
push
setting
Status
Ch 1
Ch 2
Ch 1
400
Learn actual lux
Lux
Pulse
2min
5min
700
1000
No
Lux
Lux
Lux
15min
30min
60min
Status
Status
Ch 2
Ch 1
Ch 2
Test
Short
Long
again.
On/Off
push
push
2min
5min
10min
Lock/
again.
Light 1
Light 2
LED
unlock
On/Off
On/Off
On/Off
8
30min
60min
Hours
20
50
100
200
Lux
Lux
Lux
Lux
Short
Long
Fact.
push
push
setting
300
400
Learn actual lux
Lux
Lux
500
700
1000
No
Lux
Lux
Lux
Lux
Status
Status
Ch 1
Ch 2
Ch 1
Ch 2
Pulse
2min
5min
10min
8
15min
30min
60min
Hours
Test
Short
Long
Fact.
On/Off
push
push
setting
nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
LED
On/Off
200
5.2. General operation
Lux
The integrated light sensor continuously measures the daylight level in the detection area and compares this level
to the preset lux value. Thanks to the light sensor, the light switches on automatically only if the detector detects
400
Lux
motion within the detection range and if there is insufficient daylight:
• The lighting remains switched on as long as motion is detected and the amount of daylight available in
No
Lux
the room is insufficient.
• After the last motion is detected, the lighting remains switched on for the duration of the preset switch-off
Status
Ch 2
delay (2 to 60 minutes). As soon as the switch-off delay has elapsed, the lighting switches off.
• The lighting also switches off automatically as soon as the daylight level is sufficiently high, even when
motion is still detected in the room at that time.
10min
5.3. Detection range
8
Hours
The detection area can be increased by adding an extra detector (slave) (350-20071, 350-20079 or 350-20081).
A maximum of ten slaves can be connected to one master (350-20072). The lighting is operated in accordance
Fact.
setting
with the settings on the master. Both the master and the slave have the same detection range (a circle with a
diameter of 24 m). When covering a complete area using several detectors, it is recommended to take into account
an overlap of approximately 30 % (fig. 8).
If you would like to exclude motion detection in a portion of the detection area or if the detection area is too large,
you cover the sensor lens using the cover cap supplied. This allows you to reduce the maximum range to 24 m.
The 360° detection angle can be reduced in steps of 30°.
5.4. Examples of applications
Example 1: classroom
DIP switch 1
ON
OFF
How the detector works:
- Both channels function as absence detectors. Activate the lighting by pressing the push button briefly
(daylight-independent). It is possible to switch on each channel separately (two push buttons) or together (one
push button, see § 3.3)
- The lighting is automatically switched off again after a preset time (switch-off delay), provided that no
more motion is detected by the detector in the detection area.
- Lighting can also be switched off manually (= eco off) without having to wait for the switch-off delay.
- It is also possible to hold the push button down (separately for each channel or for both channels together),
which is ideal for situations in wich the lighting should remain switched on (e.g. exam) or off (e.g. movie) for
a longer period of time:
• By pressing and holding the push button while the lighting is switched on, the lighting will be switched off.
The detector will be locked for as long as activity is detected and the preset switch-off delay + 2 hours has
not yet elapsed. After that, the detector will return to the selected settings and the lighting will be switched on.
• By pressing and holding the push button while the lighting is switched off, the lighting will be switched
on (irrespective of the daylight level). The lighting remains switched on for as long as activity is detected
and the preset switch-off delay + 2 hours has not yet elapsed. After that, the lighting will be switched off,
the detector will return to the selected settings and the lighting will be switched on.
The red indication LED on the detector flashes (0.25 s on and 5 s off) to indicate that you have pressed and held
the push button. The 'long push' function can be interrupted at any time by briefly pressing the push button, after
which the lighting will be switched on and the detector will return to the selected settings.
Example 2: office with ventilation
DIP switch 1
ON
OFF
How the detector works:
- Channel 1 functions as an absence detector, which means that lighting must be switched on by briefly
pressing the push button (daylight-dependent). Channel 2 functions as a presence detector, which means
that the ventilation is switched on automatically. To set the ventilation to light-independent, set the lux value
to ∞ (potentiometer) or "no lux" (remote control).
- The lighting is automatically switched off again after a preset time (switch-off delay), provided that no
more movement is detected by the sensor in the detection area or the light level has exceeded the preset lux
value for five minutes.
- You also have the possibility to switch off the lighting manually (=eco off)
- In addition, you can also press and hold the push button, which is ideal for situations in which the lighting
should remain switched on (e.g. exam) or off (e.g. movie) for a longer period of time:
• By pressing and holding the push button while the lighting is switched on, the lighting will be switched
off. The detector will be locked for as long as activity is detected and the preset switch-off delay + 2 hours has
not yet elapsed. After that, the detector will return to the selected settings and the lighting will be switched on.
• By pressing and holding the push button while the lighting is switched off, the lighting will be switched
on (irrespective of the daylight level). The lighting remains switched on for as long as activity is detected
and the preset switch-off delay + 2 hours has not yet elapsed. After that, the lighting will be switched off,
the detector will return to the selected settings and the lighting will be switched on.
The red indication LED on the detector flashes (0.25 s on and 5 s off) to indicate that you have pressed and held
the push button. The 'long push' function can be interrupted at any time by briefly pressing the push button, after
which the lighting will be switched on and the detector will return to the selected settings.
DIP switch 2
DIP switch 3
DIP switch 4
x
x
x
DIP switch 2
DIP switch 3
DIP switch 4
x
x
x
350-20072
x
x
11
EN
Publicité
