Ravelli Rc 120 Touch steel Manuel D'utilisation Et D'entretien page 155

Stove status
Stove State
Below are given the steps for accessing the relative menu starting from "Home" mode.
Below are given the steps for accessing the relative menu starting from Stand-By mode.
MANUFACTURER'S
TECHNICIAN
TECHNICIAN
PRODUCER
Operating phases of the appliance
Modulation
Press the key
During the work phase, the appliance should reach the room temperature set; when this condition is met, the stove switches to
"access menu" to
MODULATION mode in which fuel consumption and ventilation are minimum. access the
Operating phases of the appliance
MENU page
Modulation
During the work phase, the appliance should reach the room temperature set; when this condition is met, the stove switches to
STOVE STATE
MODULATION mode in which fuel consumption and ventilation are minimum.
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
H20 TEMPERATURE
If you wish to detect the ambient temperature by means of an external thermostat (optional), this must be connected to
In this mode you can check the proper operation of the most important parameters of the appliance. Here is a list of real data of the
the appropriate connector on the rear side of the stove; and you will have to activate the reading in "SETTINGS - EN -
stove useful for service during inspection.
ABLE THERMOSTAT." On display appears the writing TON / TOFF based on thermostat request.
- RDS current reading RDS (m/s)
- RPM current smoke extractor speed (rpm)
If you wish to detect the ambient temperature by means of an external thermostat (optional), this must be connected to
- T fumes temperture (°C)
CONNECT AN EXTERNAL THERMOSTAT WITH A SIMPLE DRY CONTACT, THEREFORE, NOT POWERED. MORE-
the appropriate connector on the rear side of the stove; and you will have to activate the reading in "SETTINGS - EN -
OVER, WE RECOMMEND YOU USE A THERMOSTAT WITH A MINIMUM OFFSET OF 3°C IF YOU INTEND TO USE - Indication of stove status
ABLE THERMOSTAT." On display appears the writing TON / TOFF based on thermostat request.
PUMP
THE COMFORT CLIMA FUNCTION.
- SET set value RDS (m/s)
3-WAY VALVE HEAT
- Df cold probe temperture RDS (°C)
CONNECT AN EXTERNAL THERMOSTAT WITH A SIMPLE DRY CONTACT, THEREFORE, NOT POWERED. MORE-
- Sk: electronic board temperature (°C
PRESSURE 1.1 BAR
OVER, WE RECOMMEND YOU USE A THERMOSTAT WITH A MINIMUM OFFSET OF 3°C IF YOU INTEND TO USE
Comfort climate
SHUTDOWN
THE COMFORT CLIMA FUNCTION.
The activation of this function enables the stove to reduce pellet consumption by activating the modulation phases, after the desired
To exit the STOVE STATUS screen and return to the Home screen, press the key repeatedly.
temperature has been reached. Subsequently, the stove checks that the temperature is maintained steady for a preset time. If this
condition is met, it automatically switches off, and on display appears the writing ECO.
In this mode you can check the proper operation of the most important parameters of the appliance. Here is a list of real data of the
The stove turns on again when the temperature drops below the set threshold.
Comfort climate
Comfort clima
stove useful for service during inspection.
The activation of this function enables the stove to reduce pellet consumption by activating the modulation phases, after the desired
The activation of this function enables the stove to reduce pellet consumption by activating the modulation phases, after the desired
Below are given the steps for accessing the relative menu.
temperature has been reached. Subsequently, the stove checks that the temperature is maintained steady for a preset time. If this
temperature has been reached. Subsequently, the stove checks that the temperature is maintained steady for a preset time (DELAY
condition is met, it automatically switches off, and on display appears the writing ECO.
- Circulator state (ON running)
SWITCH OFF). If this condition is met, it automatically switches off, and on display appears the writing ECO.
The stove turns on again when the temperature drops below the set threshold.
- Position of 3-way valve DHW (domestic hot water) or HEAT (heating);
The stove turns on again when the temperature drops below the set threshold (DELTA RESTART).
- System pressure;
Below are given the steps for accessing the relative menu.
- Stove state;
Below are given the steps for accessing the relative menu.
MANUFACTURER
ENGINEER
- Temperature read by the handheld unit;
- External thermostat (request ON);
- Flame temperature (combustion chamber);
Press the key
MANUFACTURER
- Combustion fume exhaust temperature;
"access menu" to
TECHNICIAN
access
- Inlet flow meter temperature;
the
MENU page
- Heated flow meter temp.;
- Electronic board temperature;
Press the key
"access menu" to
access
the
MENU page
To exit the STOVE STATE page and return to Stand-by page, press the button repeatedly.
Once you have accessed the Climate Comfort menu, it is possible to operate on the 3 types of settings dedicated to the function:
Once you have accessed the Comfort Clima menu, it is possible to operate on the 3 types of settings dedicated to the function:
COMFORT CLIMA
Settings
COMFORT CLIMA
Below are given the steps for accessing the relative menu starting from Stand-By mode.
Once you have accessed the Climate Comfort menu, it is possible to operate on the 3 types of settings dedicated to the function:
ENABLE COMFORT
ACTIVATE COMFORT
RESTART DELTA
DELTA RESTART
SHUTDOWN DELAY
COMFORT CLIMA
DELAY SWITCH OFF
MANUFACTURER'S
ENABLE COMFORT
RESTART DELTA
TECHNICIAN
COMFORT CLIMA
COMFORT CLIMA
SHUTDOWN DELAY
ACTIVATE COMFORT
ENABLE COMFORT
Press the key
DELTA RESTART
RESTART DELTA
"access menu" to
access the
COMFORT CLIMA
DELAY SWITCH OFF SHUTDOWN DELAY
MENU page
ENABLE COMFORT
After following the procedure above step by step, you can set the following functions:
RESTART DELTA
COMFORT CLIMA
SHUTDOWN DELAY
ENABLE COMFORT
RESTART DELTA
Use and maintenance manual Rc-Rv 120 Touch steel
Manuale utente PALMARE IDRO TOUCH RADIO
MENU MENU
USER
USER
User's manual HANDHELD TOUCH RADIO
User's manual HANDHELD TOUCH RADIO
Press the key
"confirm"
to access the
USER page
RPM g/min
STOVE STATE
T
ACTIVE PARTS
Tsk
ACTUAL STATES
STATE TEMPERATURE
H20 TEMPERATURE
POWER MOD
MENU
USER
MENU
MENU
USER
USER
Press the key
"confirm"
ENGINEER
to access the
PRODUCER
USER page
Press the key
"confirm"
to access the
USER page
MENU
USER
Press the key
"confirm"
to access the
USER page
USER
USER
POWER SETTING
LOADING AUGER
CHRONOTHERMOSTAT
CHRONOTHERMOSTAT
SCREW LOADING
SET AIR-PELLET
SET AIR-PELLET
STOVE STATUS
STOVE STATE
°C
ACTIVE PARTS
°C
ACTUAL STATES
STATE TEMPERATURE
HH T ...
EXT.T ...
FLAME T 340°C
FUME T 120°C
F. EX. T 30°C
C. EX. T
EL B. T---25°C
- Current boiler power;
- Flow read by the flow meter;
USER
- Fume extractor speed;
SCREW FEEDING - Actual flow set;
CHRONOTHERMOSTAT
AIR-PELLET SET
STOVE STATE
USER
USER
- Boiler water temperature (SUPPLY);
SCREW FEEDING
- Boiler water temperature (optional) - RETURN from the system;
LOADING AUGER
CHRONOTHERMOSTAT
- Boiler DHW temperature;
AIR-PELLET SET
CHRONOTHERMOSTAT
- Puffer temperature - average warm point;
STOVE STATE
SET AIR-PELLET
- Puffer temperature second reading (low temp.).
STOVE STATUS
ACTIVATE COMFORT ENABLE COMFORT
USER
ENABLE COMFORT
POWER SETTING
CHRONOTHERMOSTAT
SCREW LOADING
COMFORT CLIMA DELTA
DELTA COMFORT
SET AIR-PELLET
CLIMA
COMFORT CLIMA DELTA
SHUTDOWN DELAY
LOADING AUGER
CHRONOTHERMOSTAT
SET AIR-PELLET
Press the key
several times
to quickly switch to
Stove STATUS.
STOVE STATE
STATE TEMPERATURE
v H20 TEMPERATURE
T. CALDERA
T.PUFFER H
55°C
T.PUFFER L
COMFORT CLIMA
Press the key "selection" for
"selection"
to switch to the second page
of USER MENU and select
CLIMATE COMFORT.
Press the key "selection" for
"selection"
to switch to the second page
of USER MENU and select
CLIMATE COMFORT.
ENABLE COMFORT
ACTIVATE COMFORT
ENABLE COMFORT
COMFORT CLIMA DELTA
DELTA COMFORT
CLIMA
Press the key
"selection" to switch to
second menu page
COMFORT CLIMA DELTA
to the function
SETTINGS.
SHUTDOWN DELAY
Rev.1 11/03/2021
Pag.38
Vers. 01 del 07/04/15
Pag.30
USER
USER
STOVE STATE
Vers. 01 of:07.04.14
COMFROT CLIMA
Pag.23
SETTING
STOVE STATUS
Vers. 01 of:07.04.14
Pag.23
ACTIVE PARTS
ACTUAL STATES
USER
SETTINGS
USER
USER
COMFORT CLIMA
COMFORT CLIMA
SETTINGS
SETTING
USER
STOVE STATE
COMFROT CLIMA
SETTING