Black & Decker FSMH1321 Mode D'emploi page 13

• Place a cleaning pad (13) on the floor with the velcro
'loop' side facing up.
• Lightly press the steam mop down onto the cleaning pad
(13).
• Connect the steam mop to the mains.
• Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
• Turn the Autoselect™ dial (2) until the required setting is
reached. After a few seconds steam will start to come
out of the steam head.
Note! When first filled or after running dry, it can take up to
45 seconds for steam to be produced.
• It takes a few seconds for steam to enter the cleaning
pad. The steam mop will now glide easily over the
surface to be sanitized/cleaned.
• Push and pull the steam mop slowly across the surface
to thoroughly steam clean each section.
• When you have finished using the steam mop, return the
handle (8) to the upright position, making sure that it is
supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately five minutes).
Caution! It is important to monitor the water level in the
water tank. To refill the water tank and continue to
sanitize/clean stand the mop upright making sure that the
handle is supported and turn the steam mop 'OFF'. Unplug
the unit from the electrical wall outlet, and refill the water
tank.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Carpet refreshing
• Place a cleaning pad (13) on the floor with the 'loop' side
facing up.
• lightly press the steam mop down onto the cleaning pad.
• Place the carpet glider (12b) on the floor.
• Lightly press the steam mop down onto the carpet glider
until it clicks into place.
• Connect the steam mop to the mains.
• Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
• Turn the Autoselect
TM
setting.
• Push and pull the steam mop slowly across the carpet to
thoroughly refresh each section.
dial (2) to the Wood/Laminate
(Original instructions)
• When you have finished using the steam mop, return the
handle (8) to the upright position and turn the unit OFF.
Wait until the steam mop cools down (approximately five
minutes).
After use
• Turn the Autoselect
TM
• Wait until the steam mop cools down.
• Unplug the steam mop from the electrical wall outlet.
• Empty the water tank.
• Remove the cleaning pad (13) and wash it ready for next
use (take care to follow the wash care instructions printed
on the cleaning pad) (Fig. E).
• Wrap the supply cable around the cable tidy hooks (7
and 9).
• There is a hanging bracket (15) built into the hand grip
(6) which allows your steam mop to be hung from a
suitable hook on the wall. Always ensure that your wall
hook is capable of supporting the weight of the steam
mop safely (Fig. F).
Hand held steam cleaning
Warning! Maintain the unit in a horizontal position during
use.
• Attach the required accessory.
• Connect the hand held steam cleaner to the mains.
• Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
• Turn the Autoselect
TM
reached. After a few seconds steam will start to come out
of the steam head.
Note! When first filled or after running dry, it can take up to
45 seconds for steam to be produced.
• When you have finished using the hand held steam
cleaner turn the Autoselect
Turn the unit OFF by pressing the ON/OFF button (1)
and disconnect from the mains supply. Wait until the unit
cools down before storing (approximately five minutes).
Accessories
The performance of your appliance depends on the
accessory used. BLACK+DECKER accessories are
engineered to high quality standards and designed to
enhance the performance of your appliance. By using these
accessories you will get the very best from your equipment.
ENGLISH
dial (2) to the OFF position.
dial (2) until the required setting is
dial (2) to the OFF position.
TM
13