Black & Decker FSMH1321 Mode D'emploi page 11

Filling the water tank (Fig. Q)
Note! Fill the water tank with clean tap water (Do not use
any additives or chemicals).
Note! In areas of hard water, the use of de-ionised water is
recommended.
• Open the filler cap (4) by flipping it up.
• Fill the water tank with water (Do not use any additives
or chemicals).
Warning! When filling, detach from main unit and maintain
in a horizontal position.
Warning! Your water tank has a 0.5 litre capacity. Do not
over fill the tank.
• Close the filler cap (4).
Note! Ensure the filler cap is firmly secured.
Attaching the carpet glider (12b) (For use on
carpets only)
• Place the carpet glider (12b) on the floor.
• Attach a cleaning pad to the floor cleaning head (12)
• Lightly press the steam mop down onto the carpet glider
(12b) until it clicks into place.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Removing the carpet glider
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
• Return the handle (8) to the upright position and turn the
steam mop 'OFF'.
• Wait until the steam mop cools down (approximately 5
minutes).
• Place the front of your shoe onto the carpet glider
removal tab and press down firmly.
• Lift the steam mop up and off the carpet glider.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Attaching the hose and accessories to the
hand held steam cleaner (Fig. G - O)
Warning! Inspect the seal between the connection point on
the hand held steam cleaner (5) and the steam hose (16)
before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.
(Original instructions)
Attaching the hose
• Press the steam hose release button (16a) on the steam
hose (16).
• Connect the steam hose (16) to the hand held steam
cleaner (5) and release the steam hose release button
(16a) making sure it clicks into place.
Important! Ensure that the steam hose (16) is securely
connected to the hand held steam cleaner (5). If steam
escapes from the joint, the hose is incorrectly fitted. Switch
off, allow the unit to cool then remove and refit the hose.
Attaching accessories (Fig H)
• Align the lugs on the steam nozzle (17) with the recesses
on the accessory.
• Press the accessory onto the steam nozzle (17) and twist
anti-clockwise until the accessory clicks into place.
Important! All accessories, apart from the SteaMitt
which has its own hose and connector (26), must be attached
to the steam hose (16) for use.
Removing the hose and accessories
Warning! The steam hose (16), Steam nozzle (17) and
accessories become hot during use. Allow the unit and all
accessories to cool before attempting to remove.
Removing an accessory
• Twist the accessory clockwise then pull away from the
hose (16).
Removing the hose
• Press the steam hose release button (16a) on the steam
hose (16) and pull away from the hand held steam unit.
SteaMitt
TM
Your BLACK+DECKER SteaMitt
TM
sanitising and cleaning tiles, work tops, kitchen surfaces and
bathroom surfaces. This appliance is intended for indoor
household use only.
Attaching the SteaMitt
held steam unit
Warning! Inspect the seal between the connection point on
the hand held steam cleaner (5) and the SteaMitt
before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.
• Press the SteaMitt hose release button on the
TM
SteaMitt hose (26).
TM
• Connect the SteaMitt
TM
cleaner (5) and release the SteaMitt
button making sure it clicks into place.
Important! Ensure that the SteaMitt
connected to the hand held steam cleaner (5).
ENGLISH
(25)
TM
has been designed for
TM
hose to the hand
TM
hose (26)
TM
hose (26) to the hand held steam
hose release
TM
hose (26) is securely
TM
11