Black & Decker FSMH1321 Mode D'emploi page 12

ENGLISH
If steam escapes from the joint, the hose is incorrectly fitted.
Switch off, allow the unit to cool then remove and refit the
hose.
Fitting a cleaning pad to the SteaMitt
(Fig. L)
• Fit the cleaning pad (27) to the SteaMitt
attaching the 'loop' velcro strips (27a) on the upper side
of the cleaning pad, to the 'hook' velcro pads (25a) on
the underside of the SteaMitt
Warning! The SteaMitt should not be used without fitting a
TM
cleaning pad.
Note: The SteaMitt
accommodates 4 types of cleaning
TM
pads of varying thickness. Scouring pad (for use on tough
stains and non delicate surfaces), Bathroom pad (for use on
taps and other moulded bathroom surfaces), Standard pad
(for use on all larger surfaces) and Polishing pad (for use on
delicate surfaces).
Warning! Always use the SteaMitt
with your hand inside the protective glove.
Warning! Never attempt to use the SteaMitt
externally as shown in figure N. This will result in scalding.
Warning! Avoid using the SteaMitt
shown in figure O.
Warning! Should a problem occur during use, use the quick
release tab to quickly remove the SteaMitt
as shown in figure P.
Warning! Do not use the SteaMitt
windows as damage may be caused by the sudden change
in temperature.
Warning! Never point or direct the mitt at yourself or any
other person.
Note: It is recommended that the SteaMitt™ be used in
setting 1 to avoid the pad becoming too wet.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pads fitted and a continuous run
time of 90 seconds.
Switching on and off
• To switch the appliance on, press the ON/Off switch (1).
It takes approximately 15 seconds for the steam mop to
heat up.
• To switch the appliance off, press the ON/Off switch (1).
Note: always have your hand inside the SteaMitt™ before
you press the steam button.
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (8) supported
in the upright position when stationary and make sure the
steam mop is turned off when not in use.
Caution! Always empty the steam mop after use.
12
(Original instructions)
TM
(25) by
TM
(4). Press down firmly.
TM
as shown in figure M,
TM
by gripping it
TM
in tight corners as
TM
from your hand
TM
on cold glass, such as
TM
Note! When first filled or after running dry, it can take up to
45 seconds for steam to be produced.
Autoselect Technology (Fig. R)
TM
This steam mop is fitted with an Autoselect
shows various cleaning applications. They are used to select
the correct operating mode for your particular cleaning
operation.
Using Autoselect , choose from one of the following
TM
applications by turning the Autoselect
required setting is selected.
Setting Mop
Wood/Laminate
Tiles/Vinyl
Stone/Marble
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop.
Steam Burst (Fig. C1) (only available with
units FSMH1310SM, FSMH13151SM,
FSMH1321J, FSMH1321JMD, FSMH1321JSM)
The floor head (12a) is equipped with a steam burst pedal to
aid in the removal of stubborn marks and stains.
• During use, press the steam burst pedal to apply extra
cleaning power.
• To revert back to normal setting press the pedal again.
Hints for optimum use
General
Caution: Never use the steam mop without first attaching a
cleaning pad.
• Always vacuum or sweep the floor before using the
steam mop.
• The easiest way to use the appliance is to tilt the handle
to a 45º angle and clean slowly, covering a small area at
a time.
• Use water only with no additives or chemicals with your
steam mop. To remove stubborn stains from vinyl or
linoleum floors, you can pre-treat with a mild detergent
and some water before using the steam mop.
Steam Cleaning with the mop
• Fit hand held steam cleaner (5) to the steam mop body
(11)
dial (2) which
TM
dial (2) until the
TM
Hand held
Low steam flow
Medium steam flow
High steam flow