Bosch PHO Professional 2000 Notice Originale page 13

cessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of children and
u
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for mis-
u
alignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety instructions for planers
Wait for the cutter to stop before setting the tool
u
down. An exposed rotating cutter may engage the sur-
face leading to possible loss of control and serious injury.
Hold the power tool by insulated gripping surfaces,
u
because the cutter may contact its own cord. Cutting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the workpiece by your hand or against the body leaves it
unstable and may lead to loss of control.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Do not allow the chip ejector to come into contact with
u
your hands. You may be injured by rotating parts.
Never plane over metal objects, nails or screws. Cut-
u
ters and cutter shafts could become damaged and cause
increased vibration.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Bosch Power Tools
While working, always hold the planer in such a way
u
that the planer base plate lies flat against the work-
piece. Otherwise the planer could slip and cause injury.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for planing wood-based materials
such as beams and boards while resting firmly on the work-
piece. It is also suitable for chamfering edges and for rebat-
ing.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Chip ejector (PHO 2000: either right or left)
(2) Knob for setting the cutting depth (insulated gripping
surface)
(3) Cutting depth scale
(4) Changeover lever for chip ejector direction (PHO
2000)
(5) Lock-off switch for on/off switch
(6) On/off switch
(7) Storage compartment
(8) V-grooves
(9) Planer base plate
(10) Handle (insulated gripping surface)
(11) Blade head
(12) Clamping element for planer blade
(13) Fastening screw for planer blade
(14) HM/TC planer blade
(15) Hex key
English | 13
1 609 92A 83S | (08.07.2022)