Winkhaus blueMatic EAV Installation page 8

Installation instruction for cable transition T-KÜ-T1-FT (sash part & frame part) for motorised multi-point locks
Plug-in and concealed in cable transition
• inserted by plug-in function with retaining screws (3 x 20 mm)
• sash part with spring sleeve in different versions (see table)
• order frame part separately (see table)
• order cover plate separately (see operating manual blueMatic EAV / blueMotion)
• order frame part separately (see below)
• installed concealed in the airgap in different versions
• electric interface between sash and frame with 6 wires (max. 48 V DC / 2 A each wire)
between the door sash and the frame
• color silver / grey
• no routing for > 11 mm airgap needed, suitable for PVCu and aluminium entrance doors
(depends on the system), with appropriate routing it is suitable for timber doors
Recommendation: It is recommended that the cover plate (depends on the faceplate
and the material type of timber, PVCu / plastic or aluminum) conceals the routing for the
required cable reserves to prevent possible cable damage.
Technical specifications
Measurements:
Cross section of wires:
max. switching current:
max. voltage:
Screw fixing:
Part Description
T-KÜ-T1 FT 2M
plug-in and lying buried, sash part with cable 2 m + plug for motor housing
T-KÜ-T1 FT 3,5M
plug-in and lying buried, sash part with cable 2.5 m + plug for motor housing
T-KÜ-T1 FT 4,5M
plug-in and lying buried, sash part with cable 4.5 m + plug for motor housing
T-SET KÜ-T1 FT INTEG-EAV 1 + 3M
sash part with 1 m cable, end of the cable with 8-pole plug for control unit ekey home integra + connecting cable for
motor 3-wire
T-SET KÜ-T1 FT ZK-EAV 3,5 + Y 0,5M
sash part with 3.5 m cable + 5-pole plug for connection with Y-cable + Y-Kabel INSIDE EAV 0.5 m, for use with sash side
access control systems (e.g. Fingerprint IDENCOM BioKey INSIDE or ekey home SE micro)
T-SET KÜ-T1 FT ZK-EAV 1,5M + Y 0,5M
sash part with 1.5 m cable + 5-pole plug for connection with Y-cable + Y-Kabel INSIDE EAV 0.5 m, for use with sash side
access control systems (e.g. Fingerprint IDENCOM BioKey INSIDE or ekey home SE micro)
T-SET KÜ-T1 FT ZK-SO-EAV 1,5 + 3M
Set with sash part KÜ-T1-SOMMER EAV + connecting cable for motor SOMMER 3 m (for use with Sommer fingerprint
ENTRAsys FD)
T-KÜ-T1 FT EKEY MICRO (PLUS) 1,5M
sash part with cable 1.5 m + end of the cable with 5-pole plug to connect with ekey micro respectively ekey micro plus
(ready to plug in)
T-SET KÜ-T1 FT INTEG-BM 3,5 + 1,5M EST
Cable transition set T-SET KÜ-T1 FT INTEG BM including external control in housing EV-G and cable sash side 1.5 m,
cable end with 5-pole plug connector for housing EV-G + connection cable EV-G motor 3.5 m (1. cable end with
connector for housing EV-G, 2. cable end with connector for motor box BM) + connection cable EV-G INTEGRA 0,6 M
T-KÜ-T1 RT KABEL 4M
Frame part with 4 m cable and cable end sleeves (6 wires)
T-KÜ-T1 RT KABEL 0,6M RNT
Frame part with 0.6 m cable and plug for frame power supply inclusive cover strip STV-KÜ-T1 RT R8
Aug. Winkhaus GmbH & Co. KG · Berkeser Str. 6 · D-98617 Meiningen · T +49 (0) 3693 950-0 · F +49 (0) 3693 950-134 · winkhaus.de
T SB Februar 2021 · T-KÜ-T1 FT ... · Alle Rechte und Änderungen vorbehalten. / Subject to technical changes. / Sous réserve des modifications techniques.
Overall length approx. 260 mm
6 x 0,25 mm
2
2 A per connection line / wire
48 V DC
3 piece 3 x 20 mm, 1 piece 2.9 x 32 mm (included in set sash part)
Notice: Shown is the milling in the plastic
profile. For further information, see the
installation, operating and maintenance
instructions blueMotion (chapter 3.3) or
blueMatic EAV (chapter 3.2).
Figure 1: T-KÜ-T1 FT with cover plate and frame part 1
Part.-no.
5040501
5040505
5071245
5040511
Figure 2: Detail frame part 2
5040508
5085768
5040501
Figure 3: Detail T-KÜ-T1 FT without cover plate
5057683
Sash part
5040512
Frame part 1
Frame part 2
T-Cover strip KÜ-T1 RT R8
Cover plate (F16 = L 126 mm R8; F20 = L 130 mm
5040503
R10; F24 = L 134 mm square)
Screw M3 x 12 (includet in delivery from cover plate)
5040504
Fitting screw (includet in delivery from cable
transition sash part T-KÜ-T1 FT)
Installation sequence
• Frame part 1 (Figure 1):
• Drill a hole with a Ø 8 mm for cable through the door frame
• Pass the cable through the door frame (including cable reserves
in frame!)
• Fasten the frame part 1 with the fitting screw
• Frame part 2 (Figure 2):
• Drill a hole with a Ø 13 mm for cable / plug through the door frame
• Pass the Cable with plug for frame power supply through the
door frame (including cable reserves in frame!) use T-Cover strip
KÜ-T1 RT R8
• Fasten the frame part 2 with the fitting screw
Sash part with cover plate (Figure 1):
• Mill slotted hole max. 95 mm and approx. 50 mm deep
Sash part without cover plate (Figure 3):
• Drill a hole 2 x Ø 13 mm resp. oblong hole through the euro grove
(approx. 245 mm vertical under the frame part drill hole of
Ø 8 mm, depends on the profile / hinge rotation point) and for
screw pre-drill (Ø 2,5 mm)
CAUTION! The drillings must be burr-free. The spring
must be kept under a slight pre-tension even with the
door being closed (approx. 10 mm).
• Attach necessary drillings (Ø 13 mm) in the sash (e.g. in the
glazing chamber)
• Pass the cable with the plug for the motor through the door sash
• Insert the end of the spring into the sash part into the
drilling / routing into the door sash / cover plate are.
• And / or alternatively to the cover plate with screw
M3 x 12 mm fasten the sash part with fitting screw
Ø 3 x 20 mm in the fitting groove.
• Install the cable for example within the glazing chamber towards
the motor housing; install the rest of the cable for example within
the hollow section.
CAUTION! Provide cable reserve of about 3 - 5 cm for
the spring tension behind the sash part
transition!
• Complete the plug-in connection after putting the door on its
hinges
• Fix the sash part with the fitting screw Ø 3 x 20 mm
(Figure 1)
CAUTION! Release the second retaining screw
(e.g. during the installation of the door frame into the
reveal) when unhinge the door sash!
Insulate the wires not used!
Ø 3 x 20 mm
Ø 3 x 20 mm
of the cable
Seite / Page 2