Publicité
Les langues disponibles
Les langues disponibles
Important Safety Information
This symbol indicates a hazardous situation, which, if not not
avoided could result in death or serious injury.
To reduce the risks of fire or explosion, electrical shock and
the injury to persons, read and understand all instructions
included in this manual. Be familiar with the controls and
proper usage of the equipment.
HAZARD:
EXPLOSION HAZARD DUE TO INCOMPATIBLE
MATERIALS
Will cause property damage or severe injury.
PREVENTION:
•
Do not use materials containing bleach or chlorine.
•
Do not use halogenated hydrocarbon solvents such as bleach,
mildewcide, methylene chloride and 1,1,1 - trichloroethane. They are
not compatible with aluminum.
•
Contact your coating supplier about the compatibility of material with
aluminum.
HAZARD:
GENERAL
Can cause severe injury or property damage.
PREVENTION:
•
Read all instructions and safety precautions before operating any
equipment.
•
Follow all appropriate local, state, and national codes governing
ventilation, fire prevention, and operation.
•
The United States Government Safety Standards have been adopted
under the Occupational Safety and Health Act (OSHA). These
standards, particularly Part 1910 of the General Standards and Part
1926 of the Construction Standard should be consulted.
•
Use only manufacturer authorized parts. User assumes all risks
and liabilities when using parts that do not meet the minimum
specifications and safety devices of the manufacturer.
•
Before each use, check all hoses for cuts, leaks, abrasion or bulging
of cover. Check for damage or movement of couplings. Immediately
replace the hose if any of these conditions exist. Never repair a hose.
Replace it with an identical replacement hose.
•
Do not spray outdoors on windy days.
•
Wear clothing to keep paint off skin and hair.
•
Never aim the spray gun at any part of the body.
HAZARD:
HAZARDOUS VAPORS
Paints, solvents, insecticides, and other materials can be
harmful if inhaled or come in contact with the body. Vapors
can cause severe nausea, fainting, or poisoning.
PREVENTION:
•
Use a respirator or mask if vapors can be inhaled. Read
all instructions supplied with the mask to be sure it will
provide the necessary protection.
•
Wear protective eyewear.
•
Wear protective clothing as required by coating
manufacturer.
HAZARD:
SKIN BURN INJURY
Heated parts can cause severe skin burn injury.
PREVENTION:
•
Quick disconnect fittings on the hose and spray gun become hot
during use. Avoid skin contact with quick disconnect fittings
when they are hot. Allow quick disconnect fittings to cool before
disconnecting the spray gun from the hose.
English
·
Read all safety information before operating
the equipment. SAVE THESE INSTRUCTIONS.
HAZARD:
Solvent and paint fumes can explode or ignite. Property
damage and/or severe injury can occur.
PREVENTION:
Table of Contents
Safety ................................................................................................ 2
Service .............................................................................................. 3
Introduction ..................................................................................... 3
Using an HVLP Spray Gun ............................................................3-5
Cleaning your Spray Gun ................................................................ 5
Maintenance .................................................................................5-7
Converting to a Single Pin Trigger ................................................. 7
Using a Pressure Feed System .................................................... 7–8
Converting the Gun to a Regulator Gun ........................................ 8
Converting the Gun from Non-Bleeder to Bleeder ....................... 8
Choosing a Projector Set ................................................................. 9
Optional Accessories ....................................................................... 9
Material reduction/projector set chart ........................................ 10
Troubleshooting ............................................................................ 11
Turbine Cup Gun Parts List .....................................................32–33
Turbine Pressure Feed Gun Parts List ....................................34–35
Regulator Cup Gun Parts List ..................................................36–37
Compressor Pressure Feed Gun Parts List .............................38–39
Français .......................................................................................... 12
Español ........................................................................................... 22
Warranty ........................................................................................ 42
2
EXPLOSION OR FIRE
•
Provide extensive exhaust and fresh air introduction
to keep the air within the spray area free from
accumulation of flammable vapors.
•
Avoid all ignition sources such as static electric sparks,
open flames, pilot lights, and hot objects. Connecting
or disconnecting power cords or working light switches
can make sparks.
•
Do not smoke in spray area.
•
Fire extinguisher must be present and in good working order.
•
The power cord must be connected to a grounded circuit.
•
Follow the material and solvent manufacturer's safety precautions and
warnings.
•
Use extreme caution when using materials with a flashpoint below
100° F (38° C). Flashpoint is the temperature that a fluid can produce
enough vapors to ignite.
•
Plastic can cause static sparks. Never hang plastic to enclose a spray
area. Do not use plastic drop cloths when spraying flammable
materials.
Preparing to Spray........................................................................................3
Selecting a Spray Pattern ...........................................................................3
Spray Pattern Size .........................................................................................4
Adjusting the Material and Air Flow ......................................................4
Spraying ...........................................................................................................4
Adjusting the Swivel Tube ........................................................................4
Adjusting the Packing Nut ........................................................................5
Replacing the Needle Packing and Air Valve Seals ..........................5
Replacing the Check Valve, Valve Seal, and Air Tubes ....................6
Replacing the Cup Gasket .........................................................................7
Converting the Gun to Pressure Feed ...................................................7
Connecting to a 2-Quart Remote Pressure Pot System ..................8
Changing a Projector Set ...........................................................................9
© Titan Tool Inc. All rights reserved.
Publicité
