Télécharger Imprimer la page

Miles Industries valor FenderFire 611FVI Manuel

Porte simple pour les foyers 534 et 535

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

611FVI FenderFire Single Door Front
The 611FVI FenderFire Single Door Front may be fitted to any Valor model 534/535 heater, either at the time the heater
is installed or retrofitted afterwards (provided existing wall and hearth finish allow—see diagrams*). Installation of the
FenderFire door does not affect mantle clearances, framing dimensions, or other specifications listed in the heater
installation manual—see installation manual packed with the heater. The 611FVI FenderFire Single Door may also be
installed with optional 615CVI Cast Outer Plate, 616STK Stone Trim Kit (see installation instructions with kits).
Installation
1.
Install heater as per installation
instructions. Finish wall up to black frame
on heater ensuring that wall finish is flush or slightly in front of black
frame. Allow for height of finished hearth, or steel plate will not install.
2.
Remove existing top heat baffle supplied with heater and replace with
top baffle supplied with 611 kit using same 3 screws.
Note: Baffle will only install with proper side up. Do not tighten screws
all the way (see Fig. 1).
3.
Install backing plate as shown using screws provided (see Fig. 2).
4.
Clip in left and right side trim pieces. Adjust tabs by bending to fit if
necessary (see Fig. 3).
5.
Drop upper cross bar into slots (see Fig. 4).
6.
Drop door onto hinge pins.
7.
Adjust top heat baffle by opening the door and pulling it forward until so
it meets the back of the wire mesh on the door when it is closed. Tighten
screws.
8.
Drop cast iron fret into place by sliding bolts into slots of side trim. Adjust
bolts as necessary for tight fit.
9.
Clip cast iron access panel onto hooks within legs of fret.
4000710-05
for 534/535 Heaters
*Note: Wall finish must be flush or slightly
in front of this frame on heater!
Hinge Pins (3)
Drop-in
Cross Bar
Removable Cast Iron
Screen Mesh
Access Panel
Door
Screw-on
Top Baffle
Steel Back Plate
Clip-on Side Trim (LH/RH)
Cast Iron Fret
(drops into slots)
Fig. 1
Fig. 3
534/535 Heater
16" min. for
zero clearance
Fig. 2
Fig. 4

Publicité

loading

Sommaire des Matières pour Miles Industries valor FenderFire 611FVI

  • Page 1 611FVI FenderFire Single Door Front for 534/535 Heaters The 611FVI FenderFire Single Door Front may be fitted to any Valor model 534/535 heater, either at the time the heater is installed or retrofitted afterwards (provided existing wall and hearth finish allow—see diagrams*). Installation of the FenderFire door does not affect mantle clearances, framing dimensions, or other specifications listed in the heater installation manual—see installation manual packed with the heater.
  • Page 2 611FVI Porte simple FenderFire pour les foyers 534 et 535 La Porte simple FenderFire 611FVI peut être installée aux foyers 534 ou 535, soit au moment de l’installation du foyer, soit plus tard (en autant que la finition du mur et de l’âtre le permettent—voir schémas*). L’installation de la porte FenderFire n’affecte pas les dégagements du manteau de cheminée, les dimensions d’encadrement ou autres particularités listées dans le guide d’installation du foyer—voir le guide fourni avec le foyer.
  • Page 3 Screen Door Assy Porte à grillage Designed and Manufactured by / Conçue et fabriquée par Miles Industries Ltd. 190 – 2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1 Tel. (604) 984-3496 Fax (604) 984-0246 www.milesfireplaces.com © Copyright Miles Industries Ltd., 2006...