Publicité
Take the bodywork mount (item 5 – TB0218 Part 2) along with the OEM bolt that was used with the OEM
bodywork bracket, and offer into place on the rear subframe, as shown in pictures 11 & 12, ensuring the OEM
bolt is located through the hole and facing upwards, as shown in picture 13.
Fit the two M6 x 16mm long button head bolts (item 3) with two M6 washers (item 4) through the two rearward
mounting holes on the licence plate bracket from underneath the tail, then through the subframe and finally
through the mounting holes on the bodywork mount, before fitting the two remaining M6 washers (item 4) and
Page | 7
M6 nyloc nuts (item6) to the exposed ends of threads and loosely tighten, as shown in picture 14.
Ensure the licence plate bracket is correctly fitted before tightening all four nuts and bolts.
Fit the heatshrink to the wiring on the tail light and then connect the female bullet connectors supplied (item 14 –
CON0004) to the three wires on the R&G tail light.
Fit the R&G Tail Light (item 1 – LA0003) to the licence plate bracket and tighten the two nuts on the rear to
secure in place, before using the self-adhesive cable clips supplied (item 12) to neatly route the wiring, as shown
in picture 14.
To connect he LA003 to the wiring loom, the original wiring needs to be 'cut & shut'. To do this, cut the wiring
connector off the OEM tail light along with roughly 100mm of wiring. Fit the remaining three male bullet
connectors supplied to the three wires before fitting these to the bullet connectors already fitted to the LA0003
light. Connect OEM green to LA0003 black, OEM black to LA0003 yellow and OEM yellow/green to LA0003
red. Then connect the large connector to the one on the bike before checking for the correct operation of all
lights, as shown in picture 15.
Re-fit the OEM bodywork that sits on top of the tail unit, ensuring the previously positioned OEM bolt aligns
with the threaded boss in the plastic bodywork. Access this using a Phillips screwdriver though the hole on the
licence plate bracket from below and tighten, as shown in picture 16.
Fit the rubber bung supplied (item 2 – RB-80-30-00) to fill the hole in the licence plate bracket, as shown in
picture 17.
Re-fit the two OEM bolts on top of the tail unit, as shown in picture 18.
Re-fit the seat along with the two bolts on the side panels, as shown in picture 19.
Ensure the tail tidy is securely mounted.
Check that all wiring is neatly routed on the underside of the tail tidy.
Re-fit the licence plate (it may require drilling).
Depending on local laws, attach enclosed reflector in an appropriate location.
Test the licence plate illuminator and all lights before riding.
Digital copies of these instructions are available to download from www.rg-racing.com
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G
shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or
maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident
or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for
indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service
concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G
Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 04/04/2017 (AR)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
R&G Racing
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
