DeWalt D26411 Traduction De La Notice D'instructions Originale page 22

EngLIsH
before use. Many accidents are caused by poorly
maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety Instructions for Heat Guns
A fire may result if the appliance is not used with care, therefore:
• Heat may be conducted to combustible materials that
are out of sight. DO NOT use in a damp atmosphere,
where flammable gases may be present or near
combustible materials.
DO NOT apply to the same place for a long time.
•
DO NOT use in presence of an explosive atmosphere.
•
• Place the appliance on its stand after use and allow it to cool
down before storage.
DO NOT leave the tool unattended while it is switched on.
•
DO NOT place your hand over the air vents or block the vents
•
in any way.
• The nozzle and accessories of this tool become extremely hot
during use. Let these parts cool down before touching.
ALWAYS switch the tool off before putting it down.
•
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Ensure adequate ventilation as toxic fumes may be produced.
DO NOT use as a hair dryer.
•
DO NOT obstruct either the air intake or nozzle outlet, as this
•
may cause excessive heat build up resulting in damage to
the tool.
DO NOT direct the hot air blast at other people.
•
DO NOT touch the metal nozzle as it becomes very hot during
•
use and remains hot for up to 30 minutes after use.
DO NOT place the nozzle against anything while using or
•
immediately after use.
DO NOT poke anything down the nozzle as it could give you
•
an electric shock. Do not look down the nozzle while the unit is
working because of the high temperatures being produced.
DO NOT allow paint to adhere to the nozzle or scraper as it
•
could ignite after some time.
DO NOT remove the heat barrel cover during use.
•
20
Additional Safety Warnings for Heat Guns
To reduce the risk of explosion, DO NOT use in paint spray
•
booths or within 3.0 m of paint spraying operations.
DO NOT use this tool to remove paint containing lead.
•
The peelings, residue and vapors of paint may contain lead
which is poisonous.
• Hidden areas such as behind walls, ceilings, floors, soffit
boards and other panels may contain flammable materials
that could be ignited by the heat gun when working in these
locations. The ignition of these materials may not be readily
apparent and could result in property damage and injury to
persons. When working in these locations, keep the heat gun
moving in a back-and-forth motion. Lingering or pausing in
one spot could ignite the panel or the material behind it.
NOTE: These heat guns are capable of producing
temperatures in excess of 550 °C.
DO NOT use this tool to heat food.
•
DO NOT lay the heat gun on flammable surfaces when
•
operating the gun or immediately after shutting it off.
• Keep moveable items secured and steady while scraping.
• Be sure to direct the hot air blast in a safe direction; away from
other people or flammable objects.
KEEP FINGERS AWAY FROM METAL NOZZLE; it becomes
•
very hot during use and remains hot for 30 minutes after use.
Wear gloves to protect hands.
ALWAYS keep nozzle away from cord.
•
• Splinters and small particles of stripped paint can be
ignited and blown through holes and cracks in the surface
being stripped.
DO NOT burn the paint. Use the scraper provided and keep
•
the nozzle at least 25 mm away from the painted surface.
When working in a vertical direction, work downwards to
prevent paint from falling into the tool and burning.
ALWAYS use good quality scrapers and stripping knives.
•
DO NOT use the heat gun in combination with
•
chemical strippers.
DO NOT use accessory nozzles as scrapers.
•
DO NOT direct heatgun airflow directly on glass. The
•
glass may crack and could result in property damage or
personal injury.
• Maintain labels and nameplates. These carry
important information.
• Place the heat gun on a stable, level surface when not hand
held. Place the cord in a position that won't cause the heat
gun to tip over.
• Be constantly aware that this tool can ignite flammable
materials, soften or melt others. Regardless of the task you
are performing, shield or keep the heat gun away from
these materials.
• You may occasionally notice some slight smoking of the tool
after it is turned off. This is the result of heating the residual
oil that was deposited on the heating element during the
manufacturing process.
Use eye protection and other safety equipment.
•