Replacement Parts Information; Servicing Rotor, Vanes And Shaft Seals - Tuthill Fill-Rite nextec Intelligence NX25-120 Serie Manuel D'installation Et D'utilisation

| NX25-120 & NX25-240 SERIES AC FUEL TRANSFER PUMPS

Replacement Parts Information

For repairs or routine maintenance, Fill‑Rite offers the parts you need. The following parts diagram and list covers all applicable parts for your Fill‑Rite product. These parts can be
obtained through any authorized Fill‑Rite dealer. Be sure to use only genuine Fill‑Rite replacement parts for your service and maintenance needs. For a list of authorized dealers,
please visit our web site at "www.fillrite.com".
WARNING! DO NOT open or attempt to repair the motor on your NX25‑120 & NX25‑240 series pump. Opening the motor case can compromise the integrity of the
Explosion Proof construction and will void any existing warranty and certification (UL listing). Please refer to the warranty policy located on page 2.
KIT321RK - Overhaul repair kit
KIT321RG - Rotor kit
KIT320SL - Shaft seal kit
KIT321FLG - Flange kit
Servicing Rotor, Vanes, and Shaft Seals
The rotor, vanes, and shaft seals are inside the pump housing, and are accessed through
the rotor cover located on the face of the pump. It is held in place with three 4mm hex
drive attaching bolts. You can access the rotor and vanes for inspection and cleaning,
but DO NOT attempt to remove the shaft seals without a new seal kit to install.
Always inspect the rotor cover seal and mating surface (groove) for nicks or damage prior
to reassembly. Be certain o‑ring is not pinched to prevent leakage. Torque the attaching
hardware to 44 in‑lbs.
KIT321BV - Bypass kit
PART NUMBER ITEM NO. PART NUMBER
KIT321SK
1
2 SL000843-000
3 100F0790
4 100F0760
KIT321NB - Nozzle boot kit
KIT321SK - External seal kit
0 011248
REV ECN NUMBER
AS NOTED PER PART PRINTS
DENOTES DIMENSION CRITICAL TO QUALITY MATERIAL
C
NOTICE UNLESS OTHERWISE SPECIFIED
THIS DRAWING AND THE PRINCIPLES AND ELEMENTS OF DESIGN
EMBODIED THEREIN ARE THE EXCLUSIVE PROPERTY OF
TUTHILL CORPORATION, TUTHILL TRANSFER SYSTEMS AND ARE NOT TO DIMENSIONS ARE IN INCHES
BE COMMUNICATED, DISCLOSED, REPRODUCED OR USED EXCEPT AS PREVIOUSLY
TWO PLACE DECIMAL
AUTHORIZED IN WRITING BY SAID COMPANY AND MUST NOT BE SUBMITTED TO
THREE PLACE DECIMAL
OUTSIDE PARTIES FOR EXAMINATION WITHOUT THE CONSENT OF SAID COMPANY FOUR PLACE DECIMAL
ANGULAR
MUST BE RoHS COMPLIANT
MACHINED SURFACE FINISH
KIT321JC - Junction box cover kit
PART NUMBER
kit321sw
DESCRIPTION OFF/QTY.
SHIPPING ENVELOPE 1
O-RING, BUNA-N, 2-036 1
GASKET, INLET FLANGE 1
INLET SCREEN 1
DENOTES DIMENSION CRITICAL TO QUALITY
C
NOTICE THIS DRAWING AND THE PRINCIPLES AND ELEMENTS OF DESIGN
EMBODIED THEREIN ARE THE EXCLUSIVE PROPERTY OF
TUTHILL CORPORATION, TUTHILL TRANSFER SYSTEMS
BE COMMUNICATED, DISCLOSED, REPRODUCED OR USED EXCEPT AS PREVIOUSLY
AUTHORIZED IN WRITING BY SAID COMPANY AND MUST NOT BE SUBMITTED TO
OUTSIDE PARTIES FOR EXAMINATION WITHOUT THE CONSENT OF SAID COMPANY
MUST BE RoHS COMPLIANT
01/05/16
KIT, NX3200 SERIES EXTERNAL SEAL REPAIR
DATE
PART NUMBER
KIT321SK
9/1/2017
DATE
THIRD ANGLE
0.01
PROJECTION USED
0.005 DWN SCS
0.0005
0.5 1 OF 1
SHEET
64 µ" AA MAX R
ITEM NO. PART NUMBER DESCRIPTION
1 SA001885-000 ASSEMBLY; MOTOR SWITCH
2 FS001881-000 LHSHCS; M6 X 1.0 X 14MM
3 700F2950 LOCK NUT, 5/16-18
4 MF000507-001 LEVER; SWITCH
KIT321BG - Inlet kit
KIT321SW - Switch kit
0 011248 01/05/16
KIT, NX3200 SERIES SWITCH ASSEMBLY
REV ECN NUMBER DATE
PER PART PRINTS
MATERIAL
UNLESS OTHERWISE SPECIFIED
AND ARE NOT TO DIMENSIONS ARE IN INCHES 9/15/2017
THIRD ANGLE DATE
TWO PLACE DECIMAL
0.01in PROJECTION USED
THREE PLACE DECIMAL SCS
0.005in DWN
FOUR PLACE DECIMAL
0.0005in
ANGULAR 0.5° 1 OF 1
SHEET
MACHINED SURFACE FINISH 64 µ" AA MAX
KIT321ASN - Anti‑siphon kit
QTY.
1
2
1
1
PART NUMBER
kit321sw
R