Publicité
Liens rapides
ASME A112.18.1 / CSA B125.1
ICC/ANSI A117.1
Models/Modelos/Modèles
67114 & 67214
Series/Series/Seria
QUIESSENCE
®
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:
1/8" (3.17 mm)
3/32" (2.38 mm)
For easy installation of your Brizo
faucet you will need:
• To READ ALL the instructions completely
before beginning.
• To READ ALL warnings, care, and maintenance
information.
Para instalación fácil de su llave
Brizo
usted necesitará:
®
• LEER TODAS las instrucciones completamente
antes de empezar.
• LEER TODOS los avisos, cuidados, e
información de mantenimiento.
Pour installer votre robinet Brizo
facilement, vous devez:
• LIRE TOUTES les instructions avant de débuter;
• LIRE TOUS les avertissements ainsi que toutes
les instructions de nettoyage et d'entretien;
SINGLE HANDLE DECK MOUNTED ROMAN
TUB FAUCETS
LLAVES DE AGUA PARA BAÑERAS ROMANAS
CON BORDES
MITIGEURS POUR BAIGNOIRE ROMAINE -
POSE SUR PLAGE
®
?
®
"The Commonwealth of Massachusetts requires all hand-held shower sprays to comply with the Massa-
chusetts State Plumbing Code 248 CMR whereby their installation shall include a device that limits the
maximum deliverable temperature of hot water to 110°F and an approved backflow prevention system ."
"La Commonwealth de Massachusetts requiere todos los aerosoles de mano de la ducha conformarse
con el código 248 CMR de la plomería del estado de Massachusetts por el que su instalación incluya
un dispositivo que limite la temperatura entregable máxima de la agua caliente a 110°F y a un sistema
aprobado de la prevención de la expulsión."
« Le Commonwealth du Massachusetts exige de tous les pulvérisateurs tenus dans la main de douche
d'être conformes au code 248 CMR de tuyauterie d'état du Massachusetts par lequel leur installation
inclue un dispositif qui limite la température livrable maximum de l'eau chaude à 110°F et à un système
approuvé d'empêchement de refoulement. »
1
67114
1/8" (3.17mm)
67214
9/29/09 Rev. C
Publicité
Manuels Connexes pour Brizo QUIESSENCE 67114
Sommaire des Matières pour Brizo QUIESSENCE 67114
- Page 1 Inscrivez le numéro de modèle ici. You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin: 1/8" (3.17 mm) 3/32" (2.38 mm) For easy installation of your Brizo ® 1/8" (3.17mm) faucet you will need: • To READ ALL the instructions completely before beginning.
-
Page 2: Instructions De Nettoyage
This warranty excludes all industrial, commercial & business usage, whose purchasers are parts may be obtained by calling 1-877-345-BRIZO (2749) (in the U.S. and Canada) or by hereby extended a five year limited warranty from the date of purchase, with all other terms of writing to: this warranty applying except the duration of the warranty. -
Page 3: Entretien
Model 67114 RP42296s Handle with Set Screw & Button Manija con Tornillo de Ajuste y Botón Manette avec vis de calage et bouton RP42302s Maple Wood Handle RP42282s with Set Screw & Button Set Screw & Button Manija de madera del arce Tornillo de Ajuste y Botón con Tornillo de Ajuste y Botón Vis de Calage et Bouton... - Page 4 Model 67214 RP42296s Handle with Set Screw & Button Manija con Tornillo de Ajuste y Botón Manette avec vis de calage et bouton RP42302s RP61591s Maple Wood Handle Diverter Assembly with Set Screw & Button Ensamble del Desviador Manija de madera del arce Dérivation con Tornillo de Ajuste y Botón RP42282s...
- Page 5 3" min. (7.6 cm) 5"- 8" (12.7 cm - 20.3 cm) 1 1/2" (38 mm) Diameter 1 1/2" (38 mm) Diameter Finished Deck (Standard) Installation Install spout adapter (1) from below. Reinstall washer (2) on spout (NOTE: Intended for surfaces up to 2 1/2" (63.5 mm) thick.) adapter.
- Page 6 Carefully bend corrugated outlet tube (1) and insert into elbow (2). Remove test cap (1) and discard. Assemble gasket (2) onto spout (3), and install spout onto spout adapter (4). OPTION: Use silicone under the Connect elbow to spout adapter (3). Connect inlet tubes (4) to water supplies.
- Page 7 3" min. (7.6 cm) 5"- 8" Spout (12.7 cm- 20.3 cm) 2" (51 mm) Diameter Valve 1 1/2" (38 mm) Diameter Finish surface up to cardboard spacer (1). Note: Be sure to leave access to Rough Deck (Thick Tile) Installation (NOTE: Intended for surfaces tubes for soldering later.
- Page 8 Reinstall washer (1) on spout adapter. Rotate washer 90° to expose Remove test cap (1) and discard. Install spout with gasket (2) onto spout screws (2). Tighten screws (2) with a regular slotted screwdriver until adapter (3). OPTION: Use silicone under the gasket if deck is uneven. washer (1) is flush to the finished deck surface.
- Page 9 3" min. (7.6 cm) 5"- 8" (12.7 cm - 20.3 cm) 1 1/2" (38 mm) 18" (45.7 cm) Diameter Max. 1 1/2" (38 mm) Diameter 1- 1/2" (38 mm) Finished Deck (Standard) Installation Loosen screws (1) until cardboard tube (2) is free. Rotate nest (3) 90˚ (NOTE: Intended for surfaces up to 2 1/2"...
- Page 10 Tighten screws (1) with a regular slotted screwdriver. NOTE: One Insert the leader hose (1) through the spray support assembly (2). screw can be fully tightened before the other screw is tightened. Connect the leader hose (1) to the diverter outlet (3). Use Teflon ®...
- Page 11 Remove set screw (1). Remove and discard test cap (2). Install gasket (3) Remove and discard the test cap and gasket (1). and spout (4) onto spout adapter (5). OPTION: Use silicone under the gasket if deck is uneven. Be sure spout is resting firmly on the deck. Slide hose (1) through conical nut (2).
- Page 12 Install base (1) onto nest (2) and tighten. OPTION: Use silicone under Pull hose (1) to its farthest extension and point it down into the tub. Pull the base if deck is uneven. the lift rod (2) up. Move faucet handle (3) to the full on position and flush water lines for one minute.
- Page 13 3" min. (7.6 cm) 5"- 8" (12.7 cm - 20.3 cm) Spout Valve 2" (51 mm) 18" (45.7 cm) Diameter Max. 1 1/2" (38 mm) Hand Shower Diameter 2" (51 mm) Rough Deck (Thick Tile) Installation Finish surface up to cardboard spacers (1). Note: Be sure to leave (NOTE: Intended for surfaces access to tubes for soldering later.
- Page 14 Reinstall washer (1) and nest (2) on spout. Rotate washer and nest 90° to Insert the leader hose (1) through the spray support assembly (2). expose screws (3). Tighten screws (3) with a regular slotted screwdriver until Connect the leader hose (1) to the diverter outlet (3). Use Teflon ®...
- Page 15 Remove set screw (1). Remove and discard test cap (2). Install gasket (3) Remove and discard the test cap and gasket (1). and spout (4) onto spout adapter (5). OPTION: Use silicone under the gasket if deck is uneven. Be sure spout is resting firmly on the deck. Slide hose (1) through conical nut (2).
- Page 16 Install base (1) to nest (2) and tighten. OPTION: Use silicone under the Pull hose (1) to its farthest extension and point it down into the tub. Pull base if deck is uneven. the lift rod (2) up. Move faucet handle (3) to the full on position and flush water lines for one minute.