Battery Installation - Arregui SUPRA Manuel D'instructions

<EN>
IMPORTANT:
The first opening of the
safe you must use the
emergency key:
• Insert the emergency
key and turn it
anticlockwise..
NOTE: Do not store the emergency key inside the safe.

1. BATTERY INSTALLATION

Open the plastic cover located inside the door and place
4 1.5 V AA batteries.
2. PROGRAMMING THE OPENING
CODES
This safe allows to program two secret opening codes--
one standard and one master, from 3 to 6 digits each.
The initial standard code is 000000 and the initial master
code is 888888. For your security, it´s important that you
change them and configure the codes you desire.
During the process, use the
digit entered.
Programming the standard code (the safe must be
open):
A. Press 00 and the
SELECT.
B. Press the 0 button. The screen will display SET.
C. Enter your code (3 to 6 digits) and press the
button. The screen will display DONE.
With the door open, verify that the new code operates
correctly (see section 3, opening the safe).
Programming the master code (the safe may be open
or closed):
A. Press 00 and the
SELECT.
B. Press the 1 button. The screen will display OLD.
C. Enter the current master code (888888 the first
time) and press the
display SET (if the code entered is incorrect, it will
display ERROR).
D. Enter the new master code (3 to 6 digits) and press
the button. The screen will display REPEAT.
E. Enter the new master code again and press the
button. The screen will display DONE (if the code
entered is not the same both times, the screen will
display ERROR).
3. OPENING THE SAFE
Enter either of the two active opening codes, then turn
the door knob in clockwise direction to open the door
within 5 seconds.
If an incorrect code is entered, the screen will display
ERROR1, for a second incorrect attempt it will display
ERROR2, and for a third incorrect attempt it will display
- +
LOCK
button to delete the last
button. The screen will display
button. The screen will display
button. The screen will
ERROR3 and the system will remain blocked for 5 minutes,
indicating by blinking HOLD 5... HOLD 4... etc. During this
time, the keypad cannot be used.
4. CLOSING THE SAFE
Just turn the door knob in anticlockwise direction to close
the door.
5. OPENING WITH THE EMERGENCY
KEY
If you do not have the opening codes, or if the batteries
have run out and an external battery is not available, you
can open the safe using the emergency key.
For this, access the emergency lock. Introduce the key
provided with these instructions and turn it, then turn the
door knob. The safe will open.
Note: In case of an emergency opening due to a wrong
code, the emergency key opens the door but does not
unblock the electronic system.
6. OPENING WITH AN EXTERNAL
BATTERY
If the batteries have run out, you can use the safe by
placing a 9V battery in the power supply located to the
right of the keypad.
Once the safe is open, replace the batteries.
7. OTHER CONTROL ELEMENTS
SCREEN CONTROL: To configure the screen so it does not
display the digits that are entered, press the
and then the 3 button. If you would like the screen to
display what you enter, press the
SOUND CONTROL: To use the safe in silent mode, press
the button and then the 6 button. If you would like
the safe to emit sounds again, press the
again.
BATTERY STATUS CONTROL: If you would like to know
whether the batteries are sufficiently charged, press the
button while the safe is closed. If the batteries are
fine, the screen will display HI-BAT, and if they are not,
the message will be LO-BAT. In that case, you should
replace the batteries with new ones.
In any case, if the batteries are not sufficiently charged,
the system will warn you of this when the safe is opened
and closed by displaying the OPEN LO-BAT or CLOSE LO-
BAT messages on the screen, respectively.
NOTE: During the battery change process, the safe will
not forget the codes that have been entered.
button
3 button again.
6 button