Fein MKAS 355 Mode D'emploi page 30

en
30
Permissible workpiece dimensions for mitre
angle 45°
Cross-section
of workpiece
Diameter
Height x Width mm 90 x 90
Height x Width mm 90 x 100
Clamping range 185 mm (see page 9)
Permissible workpiece dimensions for mitre
angle 0°
Cross-section
of workpiece
Diameter
Height x Width mm
Height x Width mm
PRCD personal protection switch (*)
(see page 11)
The PRCD personal protection switch is specifically
intended for your protection. Do not use the PRCD
personal protection switch for switching the product
on and off.
If the personal protection switch is damaged, e.g. due
to contact with water, do not use it any more.
The PRCD personal protection switch is indispensable;
it is used for protection of the operator against electric
shock. Under fault-free operation, the personal protec-
tion switch control lamp is active.
Check the operability of the PRCD personal protection
switch before beginning to work:
1. Connect the plug of the PRCD personal protection
switch with the mains socket outlet.
2. Press the RESET–button. The personal protection
switch control lamp is active.
3. Disconnect the plug from the mains socket outlet.
The personal protection switch control lamp becomes
inactive.
4. Repeat steps 1. and 2.
5. Press the TEST–button. The personal protection
switch control lamp becomes inactive. In case the con-
trol lamp remains active, do not run the product. In this
case, contact the customer service at www.fein.com.
6. Press the RESET–button. When the control lamp is
active, the product may be switched on.
Power tool lubrication
To prolong the life of the power tool, apply oil to the
following points every month (also refer to page 16):
– Rotating part of the shaft
– Rotating part of the vice
– Gliding path of the vice
Transport (see page 4)
For transport, hook the chain and carry the power tool
by the transport handle.
Repair and customer service.
mm Ø 90
tool. The total insulation of the power tool can be
impaired. Blow out the interior of the power tool via
the ventilation slots frequently with dry and oil-free
compressed air.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
When the machine's power supply cord is damaged, it
must be replaced by the manufacturer or their repre-
sentative.
The current spares parts list for this power tool can be
mm Ø 100
found on our website at www.fein.com.
Use only original spare parts.
100 x 100
If required, you can change the following parts your-
self:
Application tools
100 x 185
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
This CE declaration is only valid for European Union
and EFTA (European Free Trade Association) countries
and only for products intended for the EU- or EFTA
market. After placing the product on the EU market the
UKCA mark loses its mark validity.
The UKCA declaration is only valid for the Great
Britain market (England, Wales and Scotland) and only
for products intended for the Great Britain market.
After placing the product on the Great Britain market
the CE mark loses its mark validity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the
last page of this Instruction Manual.
Technical documents at:
C. & E. Fein GmbH
Hans-Fein-Straße 81
73529 Schwäbisch Gmünd-Bargau, Germany
Environmental protection, disposal.
Packaging, worn out power tools and accessories
should be sorted for environmental-friendly recycling.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power