R&G LP0208BK Instructions De Montage page 6


Take this assembly and offer up to the underside of the bike, tightening the four bolts into the threaded bosses
inside the tail unit, as shown in picture 8.
If fitting Mini Indicators

To fit the R&G Mini Indicators, fit one length of heatshrink to the wires of each indicator.

Position two indicator adaptors (item 3 –I0037) onto the wiring of each indicator, ensuring the sides facing each
Page | 6
other have the raised centre profile.

Fit either indicator through the large slot on the side of the tail tidy, locating the indicator adaptors either side of
the metal bracket, before fitting the nut onto the exposed thread and tightening, as shown in pictures 9 & 10.
If fitting OEM Indicators

Remove the plastic cover from the OEM licence plate bracket by gently spreading the rear to release the clips
and then the front will dismount and the cover can be removed, as shown in picture 11.

To remove the OEM indicator, remove the plastic mounting plate from the rubber housing, as shown in picture
12, before removing the rubber mount from the licence plate bracket, as shown in picture 13. Feed the wiring out
to remove.

Fit one indicator spacer (item 2 – I0016) to both rubber indicator mounts, before fitting into the large slot on
either side of the tail tidy as shown in pictures 14 & 15. Secure in place by reusing the plastic mounting plate in
the same way that is was removed.

Feed the licence plate illuminator and indicator wiring up through the rubber bung into the tail unit and use the
cable ties provided (item 10) to neatly bundle the wires together, as shown in picture 16.

Connect one of the licence plate illuminator connectors (item 12 – CON0027) to the two bullet connectors fitted
to the licence plate illuminator wiring with the connector on the other end fitting onto the black female connector
on the OEM loom (if illumination fails, reverse the bullet connectors).

If fitting mini indicators, use the two remaining connectors (item 12 & 13 – CON0027 & CON0028) and
connect the bullet connectors to the indicator wiring, with the connectors fitting to the remaining connectors on
the OEM loom (if illumination fails, reverse the bullet connectors).

If re-fitting the OEM indicators, re-connect the connectors on the indicator wiring to the matching connector on
the OEM loom.

Check for the correct operation of all lights.

Re-fit the wiring clip and neatly route the wiring with the tail unit.

Ensure the tail tidy is securely mounted and all bolts are fully tightened.

Re-fit the seat.

Re-fit the licence plate (it may require drilling).

Depending on local laws, attach enclosed reflector in an appropriate location.

Test the licence plate illuminator and all lights before riding.
Digital copies of these instructions are available to download from
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G
shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or
maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 22/07/2016 (AR)
CONSUMER NOTICE
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
R&G Racing
www.rg-racing.com Email:
www.rg-racing.com
info@rg-racing.com