Using The Controls; Temperature Adjustment - Jennair W11310951A Guide D'utilisation Et D'entretien

Using the Controls

IMPORTANT:
The Fridge control adjusts the temperature in the refrigerator
■
compartment. The Freezer control adjusts the temperature in
the freezer compartment.
Wait 24 hours after you turn on the refrigerator before you put
■
food into it. If you add food before the refrigerator has cooled
completely, your food may spoil.
NOTE: Adjusting the temperature controls to a lower (colder)
setting will not cool the compartments any faster.
If the temperature is too warm or too cold in the refrigerator
■
or freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
The recommended settings should be correct for normal
■
household usage. The controls are set correctly when milk or
juice is as cold as you like and when ice cream is firm.
The actual temperature may differ from the display when a
■
door is open for an extended period of time.
Turning On Cooling and Viewing Set Points
The factory recommended set points are 0°F (-18°C) for the
freezer and 37°F (3°C) for the refrigerator
1. Press the FRIDGE or FREEZER touch pad.
NOTE: After the refrigerator is turned on, the Over
Temperature audio alarm and indicator light may activate
every 1½ hours until the refrigerator and freezer temperatures
are below 48°F (9°C) and 15°F (-9°C), respectively, or until the
alarm is turned off. To turn off the audio alarm and indicator
light, see "Alarm Reset."
Turning Off Cooling
1. Press the FRIDGE or FREEZER touch pad.
2. Press and hold the COOLING OFF touch pad for 3 seconds.
NOTE: To turn off the power completely, use the power
ON/ OFF switch located behind the top grille. See "Power On/
Off Switch."
Viewing the Temperature in Degrees Celsius
1. Press °C touch pad. To display degrees Fahrenheit, press °F
touch pad.
NOTE: If the freezer temperature is below zero, the negative
sign next to the freezer display will light up. This is normal.
Adjusting Controls
NOTE: Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
To Adjust Set Point Temperatures:
Press the FRIDGE or FREEZER touch pad, and then press the
■
Plus (+) or Minus (-) touch pad until the desired temperature is
reached.
Press the SAVE touch pad to program the desired
■
temperature.
NOTE: The set point range for the freezer is -5°F to 3°F (-21°C
to -16°C). The set point range for the refrigerator is 34°F to
(1°C to 6°C).
CONDITION /REASON::
REFRIGERATOR too cold
Not set correctly for conditions
REFRIGERATOR too warm
High use or room very warm
FREEZER too cold
Not set correctly for conditions
FREEZER too warm/too little
ice
High use or heavy ice use
Options
Max Ice
The Max Ice feature speeds up the ice production rate to assist
with periods of heavy ice usage.
Press OPTIONS, and then press MAX ICE to turn on the Max
■
Ice feature. Max Ice will remain activated for 24 hours unless
manually turned off.
NOTE: The temperature display for the refrigerator and freezer
compartments will remain at the user's set points, but the actual
temperature of the freezer compartment will drop to -5°F (-21°C),
while the Max Ice feature is enabled. After 24 hours, the freezer
will return to the previous temperature set point.
Max Cool
The Max Cool feature assists with full grocery loads, temporarily
warm room temperatures, or during heavy door opening use.
Press OPTIONS, and then press MAX COOL to turn on the
■
Max Cool feature. Max Cool will remain activated for 24 hours
unless manually turned off.
NOTE: The temperature display for the refrigerator compartment
will remain at the user's set point, but the actual temperature
of the refrigerator compartment will drop to 34°F (1°C), while
the Max Cool feature is enabled. After 24 hours, the refrigerator
returns to the previous temperature set points.
42°F
TEMPERATURE
ADJUSTMENT:
REFRIGERATOR Control 1°
higher
REFRIGERATOR Control 1°
lower
FREEZER Control1° higher
FREEZER Control 1° lower
7