R&G CP0376 Instructions De Montage page 8


Cut a small strip of the self-adhesive foam supplied (item 11) and stick this to the back side of
the frame mount, as shown in picture 16, in order to prevent the frame from being marked
when the crash protector kit is fitted.

Fit the spacer supplied in the kit (item 13 – S0827 – 35mm long) into the frame mount, as
shown in picture 17.

Offer the right side mounting block (item 12 – M0408) into position on the bike with the
round boss on the back sitting inside the frame mount, as shown in picture 18. The coolant
hose may need to be pulled downward in order to clear the mounting block whilst fitting.

Locate the M10 x 1.5 x 200mm long cap head bolt (item 14) with one M10 x 16mm OD
washer (item 6) fitted through the large hole in the mounting block and into the engine mount,
as shown in picture 18.

Tighten this bolt to the recommended torque settings and then tighten the pinch bolt, as shown
in picture 19.

Re-position the exhaust shield and re-fit the Torx bolt and tighten, as shown in picture 20.

Re-fit the black plastic radiator fan duct.

The crash protector can now be fitted. Slide one of the 10mm washers (item 3) onto the M10 x
1.25 x 140mm long hex head bolt (item 16) so the washer sits against head of bolt.

Slide one serrated locking washer (item 4) over the bolt so it sits against the washer just fitted.

Next slide the bolt with washers through either crash protector (item 1) so the head of the bolt
and washers go into the counter-bore, as shown in picture 21.

Locate the remaining spacer (item 15 – S0829 – 96mm long) over the exposed thread and
tighten this assembly into the remaining threaded hole on the mounting block.

Tighten the crash protector bolt until you feel some compression from inside the protector
using a 17mm socket and wrench. PLEASE NOTE THE CRASH PROTECTOR MUST
BE POSITIONED AS IN PICTURE 'C' WITH BIGGER END TOWARD FRONT OF
BIKE. Turn a little more so that you feel the compression increase slightly. Then apply a
quarter turn. Do not over tighten as damage can occur to the bike. Do not exceed 40N/m of
torque.

If not already fitted fit bubble stickers into recess of both crash protector caps.

Fit crash protector caps into both crash protectors.

Re-fit the fairings and bellypan to both sides on the bike.
Digital copies of these instructions are available to download from
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 14/11/2014 (AR)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com
CP0376
www.rg-racing.com
Email: info@rg-racing.com