Miche REVOX RC TR Manuel D'utilisation Et D'entretien page 8

own a professional spoke tension gauge. The correct spoke tension is
essential to ensure a ridged and durable wheelset.
ATTENTION in correct spoke tension, too high or too low, could lead
to wheel failure and resulting serious or fatal accident.
When replacing spokes please ensure thread lock compound is used.
COMPLETE WHEELS
4
REVOX wheels are developed to set up tire. Miche wheels are designs
for use solely on the road or dedicated cycle track with a smooth sur-
face. Please ensure that the wheels are not subject to direct shock
from poor road surfaces [i.e. pot holes] ATTENTION direct shock to
the wheels from poor road surfaces could lead to wheel failure
and resulting serious or fatal accident. In the event your wheels are
subject to any such shocks from poor road surfaces, yet do show the
signs of any damage we advise you to immediately have the wheels
checked by a qualified mechanic or other qualified person.
QUICK RELEASE
The REVOX wheels quick release has already attached in the wheel
pack.
The quick release lever has two fixed positions:
• OPEN (the text OPEN is visible)
• CLOSED (the text CLOSED is visible)
Every time you will use your bicycle, check carefully that the quick
release levers are on the position CLOSE (with the lever in closed po-
sition, on the front side of the quick release the mark CLOSE must be
present) (Pic. 6).
Warning
!
Please ensure the quick release lever is closed correctly and in the
correct position. Failure to do so could lead to wheel failure and
resulting serious or fatal accident.
All the positions different from the closed position have to be conside-
red extremely dangerous.
For the correct closing of the quick release:
• Starting from the opened position of the lever, making the nut con-
tact with the fork manually
• Bringing the lever from the opened position to the closed only with
the hand power (Pic. 7)
• Turn manually with your fingers the quick release nut until its sits
against the cycle dropout, ensuring the quick release lever is sitting
in the "open position" (Pic. 7)
• Don't use any tools (ex: tubes, extensions, ...); the closing stress has
to be felt in the passage from the opened to the closed position
(Pic. 7)
• You never have to use the quick release lever as a nut to close the
quick release, because it will injury the quick release (Pic. 8).
ATTENTION, turning the quick release lever to tighten the quick re-
lease could result in damage to the quick release and cycle frame
dropout, which could lead to wheel failure and resulting seriousse-
rious or fatal accident.
• Given that the wheels will be used on irregular surfaces, impacts,
hits or a fall can cause also damage which cannot be visible with
fast locking.
If one of these conditions is detected, please visit qualified mecha-
nic or special personnel for an accurate inspection of the locking,
since its damage may cause accidents, and serious or fatal injuries.
8 REVOX RC TR / MICHE.IT
• After every washing, remove the locking from the hub and grease the
pin completely to prevent oxidation.
INSTALLING THE CLINCHER TIRE
5
Warning
!
If you have any doubt whatsoever your service-repair ability,
please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always wear
gloves and protection glasses.
Use original spare parts exclusively provided by Fac Michelin S.r.l.
Warning
!
• Before fitting the tires, check that the diameter indicated on the tire
is 622 and the cross-section is between 25 and 32 mm, to insure that
the tire and wheel are compatible.
• Never use Latex inner tubes with this rim. The heat generated
when braking will cause the inner tube to suddenly fail, resulting
in an accident, personal injury or death.
• The use of clincher tires having a minimum diameter of 25 mm is
recommended so as to better protect the sides of the rim.
• To remove the clincher, use only plastic levers. Levers in different
material could damage the rim. A damage rim may break unex-
pectedly resulting in accidents, personal injury or death.
FITTING OF VIBROSTOP
6
Follow these simple instructions to fit the "Vibrostop"
• Clean the area of application of the "Vibrostop"
• Insert the "Vibrostop"
• Press firmly the "Vibrostop" once fitted to the rim