Balluff BOS 21M-UUI-LH31-S4 Notice D'utilisation page 29

IO-Link interface (continued)
Device-specific parameters
Index
Name Subindex
(dec)
0x0057 Operating
(87) Hours
0x00B4 SIO Output
(180) Type
0x00B6 Switch Counter
(182) Settings
0x00B7 Switch
(183) Counter State
0x00B8 Time Delay
(184) Function Q1
(Pin 4)
0x00B9 Time Delay
(185) Function Q2
(Pin 2)
0x00BA Debounce Time
(186)
0x00BB SensorPrinciple
(187)
0x00BC Pin Function
(188) Selection
0x0421 Dark
(1057) Measurement
0x0422 Integration
(1058) Time
0x0423 Maxpixel
(1059)
www.balluff.com
Name Data
(dec) format
0x01 (1) Operating UINT32
Hours
0x02 (2) Operating
Hours
Individual
0x01 (1) Q1 UINT8
0x02 (2) Q2
0x01 (1) Mode UINT8
0x02 (2) Limit UINT16
0x03 (3) Unused UINT16
0x04 (4) StartupDelay UINT8
0x01 (1) Status UINT8
0x02 (2) Counter UINT16
0x01 (1) Delay UINT8
Function
Mode
0x02 (2) Delay Time 1 UINT16
(On delay)
0x03 (3) Delay Time 2 UINT16
(Off delay,
One shot)
0x01 (1) Delay UINT8
Function
Mode
0x02 (2) Delay Time 1 UINT16
(On delay)
0x03 (3) Delay Time 2 UINT16
(Off delay,
One shot)
0x01 (1) Pin 4 UINT16
0x02 (2) Pin 2
0x00 (0) UINT8
0x01 (1) Pin 4 UINT8
0x02 (2) Pin 2
0x00 (0) UINT8
0x00 (0) UINT16
0x00 (0) UINT16
Access Value range
R
R/W 0x01 (1) = PNP
0x02 (2) = NPN
0x03 (3) = Push-Pull
R/W 0x00 (0): Off
0x01 (1): Counter Static
0x02 (2): Counter Auto
0x0001...0xFFFF (1...65535)
0
0x00...0xFF (0...255)
R Bit 0: Count Limit OK
Bit 1: Count Limit Too Low
Bit 2: Count Limit Too High
R/W 0x00 (0) = Delay
0x01 (1) = One shot
R/W 0x0000...0xFFFF (0...65535)
0 = Timing Function off
R/W 0x0000...0xFFFF (0...65535)
0 = Timing Function off
R/W 0x00 (0) = Delay
0x01 (1) = One shot
R/W 0x0000...0xFFFF (0...65535)
0 = Timing Function off
R/W 0x0000...0xFFFF (0...65535)
0 = Timing Function off
R/W 0 = Timing Function off
0x0000...0xFFFF (0...65535)
0 = Timing Function off
R/W 0x00 (0) = Background
Suppression
0x01 (1) = Background
Evaluation
R/W 0x00 (0) = Sensor Output/
Counter Output
0x00 (0) = Sensor Output
0x01 (1) = Reset Input
R/W 0x00 (0) = Disabled
0x01 (1) = Enabled
R/W 0x0001...0x02A8 (1...680)
R/W 0x0000...0xC000
(0...49152)
Remarks
Can be reset
using system
command Reset
Operating Hours
In SIO Mode
Seconds
Milliseconds
Milliseconds
Milliseconds
Milliseconds
Debounce time,
Reset input
(milliseconds)
english 11