R&G LP0233BK Instructions page 8

the indicator) over the wiring and into the hole on the bracket, before fitting the indicator nut over the wiring and
tighten onto the threaded stalk of the indicator, as shown in picture 23.
•
Fit the other indicator the same way in the remaining indicator mount, ensuring the R&G logo is facing upwards.
If fitting OEM Indicators
•
Start off by removing the OEM indicators from the OEM licence plate hanger. Cut the two cable clips, as shown
Page | 8
in picture 19, before removing the plastic piece from the rubber mount of the indicator. With this removed, pull
the rubber mount of the plastic hole and feed the indicator and wiring clear of the OEM licence plate hanger, as
shown in picture 20.
•
Locate one of the OEM indicator adaptors (item 4 – I0037) over the runner mount of the OEM indicator, as
shown in picture 21.
•
Fit each indicator to the R&G indicator bracket by feeding the indicator wiring through the large hole on the
licence plate bracket and locate the rubber with the hole, before refitting the plastic plate to secure in place, as
shown in picture 22.
•
With the indicators securely fitted, neatly route the wiring with the licence plate illuminator wiring using the
cable ties and cable clips supplied, as shown in picture 23.
•
Take the tail tidy assembly and offer it up underneath the tail whilst feeding the three sets of wires up through
the small hole where the OEM wiring exited from, as shown in picture 24.
•
Take the four M6 x 16mm long button head bolts (item 5) and four M6 washers (item 6) and fit through the four
mounting holes of the tail tidy before tightening into the threaded bosses on the subframe, as shown in picture
25.
•
Connect the licence plate illuminator wiring to the OEM connectors using the bullet connectors already fitted.
•
If using the original indicators, reconnect the connectors to those on the main loom.
•
If fitting Mini Indicators, fit one indicator connector (item 11 – CON0034) to the bullet connectors on the mini
indicator and fit the connector block to the one on the OEM wiring loom.
•
If illumination fails on any light, re-connect the bullet connectors the other way around.
•
Check for the correct operation of all lights.
•
Ensure the wiring is all neatly routed behind the panel, as shown in picture 26.
•
Re-fit the three pieces of bodywork and the hand rails in a reverse procedure of how they were removed.
•
Re-fit the licence plate (it may require drilling).
•
Depending on local laws, attach enclosed reflector in an appropriate location.
•
Test the licence plate illuminator and all lights before riding.
Digital copies of these instructions are available to download from
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G
shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or
maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident
or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for
indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service
concerned. These terms do not affect the Buyer's statutory rights.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 31/08/2017 (AR)
CONSUMER NOTICE
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
R&G Racing
www.rg-racing.com Email:
www.rg-racing.com
info@rg-racing.com