Operation - Scheppach HS110 Traduction Des Instructions D'origine

10. Operation

Switching on and off
• The saw can be switched on by pressing the green
"I" button on the on/off switch (12).
• Before you start sawing, wait until the saw blade
has reached its maximum speed.
• To switch the saw off again, press the red "0" button
on the on/off switch (12).
Adjusting the Cutting Depth (Fig. 3)
• The saw blade (4) can be (continuously) adjusted
to the required cutting depth by turning the hand
wheel for the height adjustment (9).
- Anticlockwise: reduces the cutting depth
- Clockwise: increases the cutting depth
Check the adjustment by means of a test cut.
Angle Adjustment (Fig. 3,32)
With the table circular saw it is possible to make bevel
cuts to the left at an angle of 0° to 45° to the stop rail.
m Before making every cut, check that no collision
can occur between the parallel stop (14), cross-cut-
ting gauge (31) and the saw blade (4).
• Release the locking handle (7)
• Set the desired angle on the scale by pushing in
and turning the hand wheel (9).
• Lock the locking handle (7) in the desired angular
position.
Working with the Parallel Stop (Fig. 21-27)
Adjusting the Stop Height
• The stop rail (30) of the parallel stop (14) has two
guide surfaces at different heights.
• Depending on the thickness of the material to be
cut, the stop rail (30) must be used for thick materi-
al (workpiece thickness exceeding 25 mm) and for
thin material (workpiece thickness below 25 mm).
Turning the Stop Rail
• In order to turn the stop rail (30), irst release the two
knurled nuts(m).
• Now the stop rail (30) can be pulled off the guide rail
(14) and pushed back over it again with the groove.
• Tighten the knurled nuts (m) again.
• The stop rail (30) can be attached to the left or right
of the parallel stop (14) as required. To do this, only
mount the screws from the other side of the parallel
stop (14).
Adjusting the Cutting Width
• When wooden pieces are being cut lengthwise, the
parallel stop (14) has to be used.
• The parallel stop (14) should be mounted on the
right-hand side of the saw blade (4).
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Place the parallel stop (14) from above on the guide
rail (15) for the parallel stop (14).
• On the guide rail (15) for the parallel stop (14) there
are 2 scales. These show the distance between the
stop rail (14) and saw blade (4).
• Select the suitable scale according to whether the
stop rail (30) has been turned around for working
with thick or thin material: High stop rail (thick mate-
rial) (Fig. 21); Low stop rail (thin material) (Fig. 23).
• Adjust the parallel stop (14) to the desired dimen-
sion on the inspection glass and use the eccentric
lever to fix in place for the parallel stop (13).
Adjusting the Stop Length (Fig. 26)
• In order to prevent the material being cut from jam-
ming, the stop rail (30) can be moved in the longi-
tudinal direction.
• Rule of thumb: the rear end of the stop abuts on
an imaginary line. This begins at about the middle
of the saw blade and runs towards the back at an
angle of 45°.
• Adjust the required cutting width.
• Release the knurled nuts (m) and push the stop rail
(30) forward until the imaginary 45° line is touched.
• Tighten the knurled nuts (m) again.
Adjusting the Parallel Stop (Fig. 24,25,27)
• Caution! Remove the guard.
• Adjust the saw blade (4) to the maximum cutting
depth.
• Adjust the parallel stop (14) such that the stop rail
(30) touches the saw blade (adjustment for thick
material).
• If the parallel stop (14) is not parallel to the saw
blade(4) please proceed as follows. Release the
screws (r) on the parallel stop until the parallel
stop (14) can be aligned to be parallel with the saw
blade(4).
• Retighten the screws (r).
Transverse stop (Fig. 28)
• When the wood is being cut to size, the transverse
stop (31) must be extended with the stop rail (30) of
the parallel stop (14).
• Push the transverse stop (31) into a groove (28) of
the saw table.
• Loosen the knurled screw (29).
• Turn the transverse stop (31) until the desired angle
is set. The notch on the guide bar shows the angle
that has been set.
• Retighten the knurled screw (29).
• To extend the lateral end stop (31) with the end stop
rail (30), the end stop rail (30) must be removed
from the parallel end stop (14). Now the stop rail
has to be mounted as shown in Figure 29; use the
knurled nuts (m) for this purpose.
GB | 37