Attachment And Operation - Scheppach HBS400 Mode D'emploi

Wear hearing protection.
The effects of noise can cause a loss of hearing. To-
tal vibration values (vector sum - three directions) de-
termined in accordance with EN 61029.

8. Attachment and operation

Before starting the equipment
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
Make sure the machine stands securely, i.e. bolt it to
a workbench or solid base. There are two holes for
this purpose in the machine foot.
• The saw table must be mounted correctly.
• All covers and safety devices have to be properly
fitted before the machine is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws etc.
• Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
• Before you connect the machine to the power sup-
ply, make sure the data on the rating plate is the
same as that for your mains.
Assembly tools
• 1 engineer's wrench SW 10/13
8.1 Mounting the base (Fig. B+C+D)
Installation parts:
• 4 stand feet (a)
• stand braces below: 2 x long (b) + 2 x short (c)
• stand braces above: 2 x long (d) + 2 x short (e)
• 4 rubber feet (f), 4 washer 8, 4 nuts M8
• Mounting parts (24 carriage bolts M8x16, 4 hex
screws M8x45, 32 washer 8, 28 nuts M8 4 Locking
rings M8)
• 2 wheels with wheel mounting (g) (2 locking screws
M8x20, 2 washers 8, 2 stop nuts M8).
• Hand-tighten all screws lightly during the installation.
• Place the 4 rubber feet on the stand feet.
28 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Attach one stand brace below (b+c) each with 2
screws M8 x 16, 2 washer and 2 nuts to the stand
feet (a).
• Mount the frame struts above (d+e), each with 4
carriage bolts M8 x 16, 4 washers and 4 nuts on the
frame feet (a) as shown in Fig. C.
• Fit the two wheels using wheel mounting (g) with 2
locking bolts M8x20; 2 washers 8 and 2 lock nuts
M8 (Fig. C+D)
• Place a cardboard box behind the machine and
then carefully tip the machine backward until the
machine rests on its housing.
• Place the previously assembled frame (Fig. C) un-
der the base plate of the band saw; screw it into
place by hand with 4 hex bolts M8x45, 8 washers, 4
circlips and 4 hex nuts.
• Set the machine with the base on a level surface
and tighten all the screws and nuts firmly.
8.2 Assembling the work table (Fig. E - J)
• Lay the table insert (h) in the recess in the work
table intended for this (7) (Fig. E). (To replace, dis-
assemble the work table in reverse order.)
• Place the band saw blade through the slot on the
machine table. Place the machine table on the ta-
ble guide so that the fixing screw (i) fits through the
bracket (j). (Fig. F+G)
• Screw the machine table tight with the wing nut (k)
(Fig. E+H).
• Check that the bandsaw blade runs freely and does
not touch the table.
• Fit the bolt M6x40 with two washers and the nut to
the table. (Fig. I)
• Using the adjustment
just the table
– Use a set square –
• Counter the adjustment screw (l) and tighten the
wing nut (k).
• Set the scale pointer (m) to 0.
• Adjust the angle scale (o):
• By loosening the screws (n) and shifting the angle
scale (o) until the scale pointer (m) points to 0. Fix
screws.
8.3 Fitting the table width enlargement (Fig.
K+L+M+N+O)
Remove the two bolts and washers (p) from the table
width enlargement (6). (Fig. K)
Slide the table width enlargement (6) onto the table
mounted on the machine. Ensure that the clamping
lever (8) is open (Fig. L+M).
Push the table width enlargement fully onto the table
(Fig. N) in order to fix the two bolts (p) on both sides.
(Fig. O) Be sure to fit the bolts (p) on both sides. The
two bolts are used to limit the extension of the table
width enlargement.
screw (l) to ad-
to a right-angle.