Utilisation; Technical Features; Electrical Connections; Electrical Safety - Husqvarna TS 2301 Manuel D'utilisation Et D'entretien

This symbol indicates that the
machine is in conformance with
the applicable European directive.
MANDATORY
WARNING
These signs give advice
concerning your safety
Instruction plate
MANUFACTURER
TYPE TYPE
FABRICATION
WEIGHT MASSE UTILE Kg
MAXI TOOL Ø MAXI OUTIL. mm
BORE Ø ALESAGE mm
SPEED T/MN - RPM
1

Utilisation

• Utilisation : Water-cooled cutting of tile
materials.
• Blade with continuous rim Ø 230 mm (D)
bore Øx25.4 mm (AL).
Use only continuous rim diamand
blades.
• Cutting thickness (material) :
to 90° : 55 mm - to 45° : 40 mm
• Cutting width (Lg) with guide at 90° :
290xmm.
• Length of cut unlimited.
2

Technical features

• Power : 0.9 CV (700 W)
• Voltage : 230 V - 50 Hz
• Motor speed : 2800 rpm
• Dimensions (mm) l x w x h :
550 x 570 x 280
• Weight : 15 kg
• Blade cooling by partial immersion
• Tank capacity : 3 litres (autonomy
15xminutes cutting)
• Power cable : HO5 VVF 3 x 0.75 mm
length 1,50xm.
POWER
MODEL
LEVEL
Lwa (dB)
EN ISO 3744
0.7 KW 240 V 76
0.7 KW 115 V 74
7
3
INDICATION
INFORMATION
INSTRUCTION
PROHIBITION
N° SERIE SERIAL
FABRICATION
ANNEE DE
YEAR
PUISSANCE kW POWER
PLAGE DE
V VOLTAGE
TENSION
FREQUENCE Hz FREQUENCY
INT. UTIL. A INTENSITY
4
2
-
PRESSURE VIBRATION
LEVEL LEVEL
Lpa (dB) NF
EN ISO 4871 EN V 25349
60 0.06
60 0.06
Pre-use check-list
Before use, read the instructions
carefully and familiarise yourself
with the machine.
The working area must be
perfectly tidy, well lit and must
offer no risks (no humidity or
dangerous products in the
vicinity).
The operator must wear
suitable protection when
working.
Any unauthorised persons must
be kept away from the working
area.
Use blades suitable for the work
to be done (speed, geometry,
application, etc.)

Electrical connections

- ELECTRICAL SAFETY :

Operate this machine only on a
supply equipped with a 30 mA
earthed current-limiting circuit-
breaker. Otherwise, consult our
catalogue for appropriate models.
- The RCCB must be used
correctly, including testing it
regularly. For tools supplied
with an integral RCCB in the
cable or in the mains plug, if
the cable or plug has been
damaged, repairs must be
carried out by
manufacturer, one of his
agents or by a qualified repair
workshop to avoid any risks
resulting from errors.
- Check the mains voltage is
identical to that shown on the
instruction plate N on the
machine [FIG.x1]
- Use twin & earth plugs S.T.D. 3
pin plug 240 V.
- Extension cable : cable section
adequate for the electric power,
connection to the main by a type
HO7 RNF cable of 2.5 mm
section up to 50 m.
5 Fitting the blade
A
N
FIG. 1
• Disconnect the machine.
• Remove the disk covers (A) and (B).
• Remove the water bath (C).
• Unscrew the tightening nut right-hand
thread (D).
• Remove the outer flange (E). The blade is
tightened by hand, or use a spanner as
appropriate.
• Fit the diamond blade.
Rotation direction is indicated by
an arrow on one side of the
blade.
Make sure the contact faces of
flanges, of blade and the axle are
clean
• Check correct centring of the blade.
• Replace the outer flange and lock the nut.
• Check that the disk is centred.
the
6 Starting up
Always take care.
Get into a comfortable, balanced
position.
Remove all adjustment tools and
wrenches from
machine
Keep the protective covers in
place while the machine is
operating.
• Fill the water bath.
• Connect the machine to the mains.
2
• Start by means of the on-off switch
E
D
B
C
floor and
I
.