Device Information - Dimplex WI 50TU Instructions D'installation Et D'utilisation

12 Device information

1 Type and order code
2 Design
2.1 Model / controller
2.2 Thermal energy meter
2.3 Installation location / degree of protection according to EN 60 529
2.4 Water in device protected against freezing
2.5 Performance levels
3 Operating limits
3.1 Heating water flow / return
3.2 Cold water (heat source)
4 Performance data / flow rate
4.1 Heating water flow rate with an internal pressure differential of
Minimum heating water flow rate
4.2 Cold water flow rate at an interal pressure differential of
3
4.3 Heat output / COP
4.4 Sound power level
4.5 Sound pressure level at a distance of 1m
5 Dimensions; weight and filling quantities
5.1 Device dimensions without connections
5.2 Device connections for heating
5.3 Device connections for heat source
5.4 Weight of the transportable unit(s) incl. packaging
5.5 Refrigerant; total filling weight0
5.6 Lubricant; total filling quantity
6 Electrical connection
6.1 Load voltage; Fuse protection
6.2 Control voltage; Fuse protection
6.3 Starting current with soft starter
6.4 Nominal power consumption W10 / W35 / max. consumption
Nominal current W10/W35 / cos ϕ
6.5
6.6 Power consumption of compressor protection
(per compressor)
7 Complies with the European safety regulations
1. The heat circulating pump and the heat pump controller must always be ready for operation.
2. The given well water flow rate is identical for all operating points.
3. These data indicate the size and capacity of the system according to EN 255 / EN14511. For an analysis of the economic and energy efficiency of the system, the bivalence point
and regulation should be taken into consideration. The specified values, e.g. W10/W55, have the following meaning: Heat source temperature 10 °C and heating water flow tem-
perature 55°C.
4. The temperature spread of 5K is based on the standard value of W10 / W35 in operation with 2 compressors.
5. Operation with 2 compressors.
6. Operation with 1 compressor.
7. The specified sound pressure level corresponds to the operating noise of the heat pump in heating operation with a flow temperature of 35°C. The specified sound pressure level
represents the free sound area level. The measured value can deviate by up to 16 dB(A), depending on the installation location.
8. Please note that additional space is required for pipe connections, operation and maintenance.
9. See CE certificate of conformity.
www.dimplex.de
All manuals and user guides at all-guides.com
1
°C
°C
W10 / W35/30 m³/h / Pa
W10 / W45/38 m³/h / Pa
W10 / W55/45 m³/h / Pa
2
W10/7 W35 m³/h / Pa
at W10 / W55 kW / ---
kW / ---
at W10 / W45 kW / ---
kW / ---
at W10 / W35 kW / ---
kW / ---
dB(A)
7
dB(A)
8
H x Wx L mm
Inches
Inches
kg
Type / kg
Type / litres
A
3
kW
A / ---
W
WI 50TU
Universal / internal
Integrated
Indoor / IP 21
Yes
2
up to 58 ± 2
+7 to+25
4
10K
5K
5
43,3 / 3,5
6
22,2 / 3,6
5
45,5 / 4,5
6
23,7 / 4,6
5
49,0 / 6,1 47,3 / 5,7
6
26,3 / 6,3 25,1 / 5,9
59
44
1660 x 1000 x 775
R 1 1/2" Int. Thread
R 2" Int. Thread
373
R404A / 7,5
Polyolester (POE) / 3,8
3~/PE 400V (50Hz) / 32AT
1~/N/PE 230V (50Hz) / 13A
29
8,3 / 12,8
14,9 / 0,8
70; thermostat controlled
12
WI 100TU
Universal / internal
Integrated
Indoor / IP 21
Yes
2
up to 58 ± 2
+7 to+25
16.5 / 17700
11.3 / 9100
7.5 / 4500
21.2 / 21700
4
10K
5K
86,7 / 3,3
40,2 / 3,0
90,9 / 4,1
47,6 / 4,3
98,5 / 5,6 95,5 / 5,3
52,8 / 6,1 51,7 / 5,8
70
56
1890 x 1350 x 775
R 2" Int. Thread
R 2 1/2" Int. Thread
593
R404A / 15,8
Polyolester (POE) / 6.5
3~/PE 400V (50Hz) / 36AT
1~/N/PE 230V (50Hz) / 13A
100
18,0 / 28,4
33,4 / 0,8
70; thermostat controlled
9
E-9