Topcom Lucca Mode D'emploi page 22

switched on or off). If the machine is in "Answering mode with possibility to
leave a message", the display shows the number of received messages. If the
machine is in "Answering mode without possibility to leave a message", the
display shows "AO" (answer only).
2. Shortly press the ON/OFF button again to switch off the answering mode. The
machine will say "Answer off"/"Antwort aus" and the display shows "—".
2. OUTGOING MESSAGES
OUTGOING MESSAGE ONE
The answering machine has a standard "Outgoing Message One" to answer calls
if no outgoing message has been registered or if the registered outgoing mes-
sage has been erased after a power failure. This standard outgoing message is as
follows: "Sorry, I can't answer your call now. Please leave your message after the
beep tone."/"Ich kann im Moment Ihren Anruf nicht entgegennehmen, bitte hin-
terlassen Sie Ihre Nachricht nach dem Signalton." You can also register your own
"Outgoing Message One".
REGISTERING OUTGOING MESSAGE ONE
1. Set the answering machine to "Answering mode with possibility to leave a
message" by holding down the ON/OFF button until the machine says:
"Announcement one on"/"Ansage eins ein".
2. Hold down the OGM button and as soon as you hear the beep tone you can
start saying your outgoing message. The outgoing message can have a maxi-
mum duration of one minute. The display shows the regristration time from 0
to 59. As the counter reaches 59, you hear a short beep tone and the registra-
tion time will be ended.
3. As soon as you have finished your outgoing message, release the OGM but-
ton.
4. Now the machine will repeat the outgoing message to confirm your registra-
tion.
CHECKING OUTGOING MESSAGE ONE
1. Set the answering machine to "Answering mode with possibility to leave a
message" by holding down the ON/OFF button until the machine says:
"Announcement one on"/"Ansage eins ein".
2. Press the OGM button: the machine will play back the outgoing message.
3. If no OGM was registered, you will hear standard "Outgoing Message 1":
38
Lucca
"Sorry, I can't answer your call now. Please leave your message after the beep
tone."/"Ich kann im Moment Ihren Anruf nicht entgegennehmen, bitte hinter-
lassen Sie Ihre Nachricht nach dem Signalton."
4. Press STOP to stop message playback.
ERASE OUTGOING MESSAGE ONE
1. Set the answering machine to "Answering mode with possibility to leave a
message by holding down the ON/OFF button until the machine says:
"Announcement one on"/"Ansage eins ein".
2. Press the OGM button. The machine will play back your OGM 1.
3. Press the ERASE button during OGM playback.
4. Th e machi ne will era se the mess age a nd says: "Announc ement
erased"/"Ansage gelöscht".
5. Standard message one comes instead.
OUTGOING MESSAGE TWO
The answering machine does not have a standard "message two". If you set your
answering machine in "Answering mode without possibility to leave a message"
without first having registered a message two, you will hear: "Record announce-
ment"/"Bitte nehmen Sie den Ansagetext auf".
REGISTERING OUTGOING MESSAGE TWO
1. Set the answering machine to "Answering mode without possibility to leave a
message" by holding down the ON/OFF button until the machine says:
"Announcement two on"/"Ansage zwei ein".
2. Hold down the OGM button and as soon as you hear the beep tone, start say-
ing your OGM. There is no time limit for OGM 2. The display shows the regis-
tration time from 0 to 59. As the counter reaches 59 it automatically starts
from 0 again.
3. Release the OGM button as soon as you have finished your OGM.
4. Now the machine will repeat the outgoing message to confirm your registra-
tion.
CHECKING OUTGOING MESSAGE TWO
1. Set the answering machine to "Answering mode without possibility to leave a
message" by holding down the ON/OFF button until the machine says:
"Announcement two on"/"Ansage zwei ein".
2. Press the OGM button: the machine will play back the outgoing message.
3. Press STOP to stop message playback.
39
Lucca