GYS EXAGON 400 CC Mode D'emploi page 20

ASSISTANCE FOR SETTING UP AND SELECTING CONSUMABLES
0.3 - 3 mm
DC
2.4 - 6 mm
4 - 8 mm
6.8 - 8.8 mm
9 - 12 mm
ELECTRODE GRINDING
d
SEMI-AUTOMATIC MIG / MAG WELDING WITH WIRE FEEDER (EXAFEED
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the positive (+) or negative (-) terminal depending on the wire type
• Connect the connection cable on the remaining power connector,
• Plug the connection cable's command connector on the 10 points base situated between the two power connectors (FIG-1, n°5),
• Refer to the wire feeder's user manual for the remaining connections.
MODE SELECTION AND SETTINGS
Press the button several times until the LED light switches on below the
symbol .
Both display show - - - and the knobs are inactive, all controls are now opera-
ted from the wire feeder's interface (Refer to the wire feeder's user manual for
the control settings).
SEMI-AUTOMATIC MIG / MAG WELDING WITH VOLTAGE DETECTING WIRE FEEDER (
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the positive (+) or negative (-) terminal depending on the wire type
• Connect the wire feeder on the connector using a male-female cable (NOMAD CABLE),
• Refer to the wire feeder's user manual for the remaining connections.
MODE SELECTION AND SETTINGS
Press the button several times until the LED light switches on below the
symbol .
1. Setting the welding voltage :
Adjust the welding voltage using the main knob
to be carried out. The voltage setpoint is indicated on the left side display.
2. Inductance settings :
Adjust the inductance level using the second knob
-9 to +9. The lower the inductance level, the harder and more guiding the arc.
The higher the inductance and the softer the arc with little splatter.
CARBON ARC GOUGING
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the negative (-) terminal
• Connect the gouging torch on the positive (+) terminal
• Orient the clamp depending on the working position, make sure that the compressed air flows in the arc's direction and not the other way around.
• Place a carbon electrode,
• Connect the compressed air to the gouging torch,
The arc strike is easier : just make contact with the piece, and advance while pushing the electrodes towards the metal to be removed.
20
EXAGON 400 CC/CV
Current (A) Electrode (mm)
5 - 75
60 - 150
100 - 200
170 - 220
255 - 300
L = 3 x d for a low current.
L = 3 x d for a high current
L
depending on the work
, a relative value from
Shroud (mm)
1 6.5
1.6 8
2 9.5
2.4 11
3.2 12.5
(in general on the -)
VRD
V
ARC FORCE
INDUCTANCE
The grey areas are not useful for this mode.
(in general on the -)
VRD
V
The grey areas are not useful for this mode.
Argon flow rate (L/min)
6 - 7
6 - 7
7 - 8
8 - 9
9 - 10
)
,
M A D E I N F R A N C E
MMA
A
press 3 s
Basic
7018
0
Rutile
6013
Cellulosic
6010
press 3s
-9 +9
memory
)
,
M A D E I N F R A N C E
MMA
A
press 3 s
Basic
7018
0
Rutile
6013
Cellulosic
6010
ARC FORCE
INDUCTANCE
press 3s
-9 +9
EN
MIG TIG Gouging
CV
MODE
press 3s
setup
MIG TIG Gouging
CV
MODE
press 3s
setup
memory