Arregui FORMA EVOLUTION Mode D'emploi page 11

WORKING INSTRUCTIONS FOR
FORMA EVOLUTION
• To open the safe for the first time, see Point 1: "Initial
opening".
• For subsequent safe opening, type in one of the opening
codes which the safe has available, and then turn the knob.
The initial factory-set user code is 1234, and the super-user
code is 123456.To learn how to open and close the safe,
see Point 2: 2. "Safe opening and closing".
• For security reasons, it is necessary to change the initial
codes from the Factory setting user and super-user codes
and key in the numbers you choose. The new codes may
have between 3 and 8 digits. To learn how to change the
codes, see Point 3. "Changing opening codes".
• Top activate the delay function, see Point: 4. "Screen and
sound setting configuration adjustments".
• For other setting adjustments, see Point: 5. "Emergency
opening"
• In the event of any anomaly, such as batteries discharging,
for example, the safe has an external power outlet available
by means of a micro USB connector; see Point: 6." Use of
the external feed". In any case, to avoid drainage of the
batteries, please see Point: 7. "Battery level indicator". In
the event that the batteries become drained and you wish to
replace them, see Point 8. "Replacement of the batteries".
• Identification of the safe is done through the serial number
to be found on the front of the door and on the cover of
these instructions, which you will need in order to request
emergency openings, or spare parts, etc...
1. INITIAL OPENING
Proceed with the safe opening in the following manner:
• Insert the emergency key (gold colored), which you'll find in
the envelope, in the lock.
• Give a half-turn towards the right (in a clockwise direction)
• Now give a half-turn towards the left (in an anti- clockwise
direction), returning to the initial position, and take out the
key.
• Insert the user key (silver-colored) and give it two half-turns
to the right. Open the safe.
For proper functioning the safe requires 4 x alkaline batteries
1,5V (AA), which are placed in the battery holder situated at
the rear part of the door. To put them in place, open the lid
on the battery carrier and insert batteries as per the diagram
which you'll find inside. Once completed, the electronic
system will be activated.
To close the safe, simply make a half-turn towards the left (in
an anti- clockwise direction).
A5 instrucciones FORMA EVOLUTION 2020.indd 11
2. OPENING AND CLOSING OF THE SAFE
• Introduce the user key (silver-plated) into the lock
• Press the key, the keyboard will show "--------"
• Type in your opening user- or super- user code. The screen
will continue showing the digits as you type them. If you
make a mistake and type in a mistaken code, you can type
in the code again just by typing the
• Press the enter key. If the code typed is correct a
long beep will sound and the screen will display "OPEN"
for 5 seconds. Give the knob two half-turns to the right
(clockwise) to open the safe. If the code typed is incorrect,
4 short beeps will sound and the screen will display "ERROR
1". In this event, start the process again. "ERROR 2" will
show if the screen starts to wander again. The box allows
a maximum of 5 mis-entered attempts before displaying
"ERROR 5", before blocking new attempts for 5 minutes as
a security measure. During this period, the keypad will be
locked and the screen will display the "LOCKED 5" message,
indicating that a 5-minute blockage is in place. If any key
is touched during the 5 minute blocking period, the Word
LOCKED will appear on screen followed by a number which
indicates the number of minutes of blockage remaining
("LOCKED 4", "LOCKED 3"...). Once the last minute has been
entered, there will be a 60-second countdown.
• To close the box simply turn the knob to the left (in an anti-
clockwise direction).
3. CHANGING THE OPENING CODES
The box has two opening codes available, a user code and
super-user code. Initially the codes are 1234 for the user code,
and 123456 for the super-user code.
To change the user code, proceed in the following manner:
• Open the box and don't close it until the procedure is
complete
• Press the button located inside the box. The box will emit
a long whistle and the screen will display the "NEW CODE"
message.
• Introduce the new code from 3 to 8 digits and confirm
by pressing the enter key. The screen will display the
"AGAIN" message.
• Introduce the new code and confirm with the
The box will emit a long acceptance beep, and the screen
will display the "U-CODE R" message, to indicate that it has
been registered.
To change the super-user code, proceed in the following
manner:
• Open the box and don't close it until the procedure is
complete.
• Hit the key.
• Hit the 8 key.
• Press the button located inside the box. The box will emit
En
key again.
enter key.
29/10/20 9:45