Putting Into Operation - Thomas VAPORO TROLLEY Mode D'emploi

Upholstery and floor nozzle (13)
You can use the floor nozzle with or without the cloth.
However, sensitive surfaces should be cleaned with the
cloth. The cloth is fastened to the floor nozzle very easily
by pressing down the spring clips, inserting the cloth and
releasing the spring clips again.
NOTE: For packing reasons the floor nozzle is
delivered with the connection turned the other
way round. Please turn the connection clockwise or anti-
clockwise in the holder until it points upwards when you
use the floor and upholstery nozzle.
Window nozzle (15)
Perfect for cleaning large window surfaces, to choice
with the appropriate cleaning cloth (for example win-
dow panes, mirrors, etc.).
Punctiform nozzle (16)
This is used to eliminate small patches of dirt and clean-
ing in narrow not easily accessible areas. The metal noz-
zle can also be unscrewed. Fit the round brush (17) and
use to remove stubborn dirt.
Cleaning cloth (18)
Fasten the cleaning cloth to the upholstery and floor nozzle
for cleaning hard floors such as tiles, PVC covering, etc.
All accessory parts are connected together by means of
a locking mechanism. To this end the respective locking
and unlocking button must be engaged in the appropri-
ate opening. If you want to take off the accessory part
again just press the button to lock or unlock, before
removing the accessory part.
3: To fill water tank
CAUTION! Risk of scolding! Press the steam
safety valve (8) downwards to open it to allow
any pressure given on the inside to escape. Should the
boiler still be under pressure you will not be able to
unscrew the steam safety valve.
Should you have no distilled water to hand you can also
use tap water as a temporary measure. However, water
from the tap should always be hot to save you both time
and electricity. To avoid lime deposits in the boiler we
recommend that you always use distilled water as far as
this is possible.
Never fill the tank with detergents, scents or other
chemical substances! Always use the funnel to fill
the tank with water.
All manuals and user guides at all-guides.com
Always close the water tank again. To do this screw up
the steam safety valve in the thread until you feel a slight
resistance. Now press the locking screw downwards
until it is in the right position and turn clockwise until it
fits firmly.
4: Insert mains plug into the mains plug box.

Putting into operation

To switch on
Press the on/off switch on the side where the symbol
„I" is. The control lamp in the on/off switch will light up.
After approx. 5 minutes the appliance will be ready for
use and the green control lamp will come on. You will
hear the boiler making a slight noise while the appliance
is building up pressure.
To switch off
Press the on/off switch on the side marked with the sym-
bol „O". The control lamp in the on/off switch will no
longer light up.
generated until there is no more water left in the tank or
the appliance has been switched off by means of the on/
off switch. The handle will become warm and the nozzle
hot when using the appliance for any length of time!
at least 50 cm away from the glass. There is a risk of the
glass cracking if this is not be observed!
start to clean again. Please always pour this water down
the drain or in a bath tub. Otherwise, there is a risk of
the hot water spitting out of the appliance.
faces may be damaged. Always first test when neces-
sary at some point which is not too obvious. In the case
of cleaning sensitive surfaces (for example plants)
always please hold the nozzle away at least some 20 to
40 cm away and avoid direct contact with steam.
CAUTION! Hot steam will escape for as long as
the steam button is pressed down. Steam will be
CAUTION! When cleaning cold glass surfaces
you should always begin by holding the nozzle
CAUTION! Hot water can be left in the hose
every time you switch the cleaner on and you
IMPORTANT! Do not clean sensitive surfaces
should you have any doubt otherwise such sur-
11