Set Up/Installation - Jøtul I 80 RH Manuel D'installation Et D'utilisation

ENGLISH
4.5 Chimney
• The fireplace can be connected to a chimney and flue
pipe approved for solid fuel fired fireplaces with flue gas
temperatures specified in «2.0 Technical data».
• The chimney's cross-section must be at least as big as the flue
pipe's cross-section. See «2.0 Technical data» when calculating
the correct chimney cross-section.
• Connection to the chimney must be carried out in accordance
with the installation instructions from the supplier of the
chimney.
• Before making a hole in the chimney the fireplace should be
test-mounted in order to correctly mark the position of the
fireplace and the hole in the chimney. See fig. 1 for minimum
dimensions.
• Ensure that the flue pipe is inclined all the way up to the
chimney.
• Use a flue pipe bend with a sweeping hatch that allows it to
be swept.
Be aware of the fact that connections must have a certain
flexibility in order to prevent movement in the installation
leading to cracks.
N.B. A correct and sealed connection is very important for the
proper functioning of the product.
Warning! Weight from the fireplace must not be transferred to the
chimney. The fireplace must not interfere with the ability of the
chimney to move and it must not be fastened to the chimney.
Note: A guide is published by the British Flue and Chimney
Manufacturers' Association which contains general information
on chimneys and flues.
Recommended chimney draught, see «2.0 Technical data». If the
draught is too strong you can install and operate a flue damper
to control the draught.
In case of chimney fire
• Close all hatches and vents.
• Keep the firebox door closed.
• Check the loft and cellar for smoke.
• Call the fire service.
• Before use after a fire an expert must check the fireplace in
order to ensure that it is fully functional.
4.6 Preparation/installation
Make sure that the fireplace insert is free of damage before
commencing with the installation.
The product is heavy! Make sure you have assistance when
erecting and installing the fireplace.
Attaching the legs (fig. 3) and securing the
base heat shield
1. Unpack the insert. Take the box out with its contents and if
necessary, the burn plates. Remove both the ash lip and the
bottom frame (applies to Harmony/Panorama) situated at
the rear of the combustion chamber. Close the doors.
2. To make the installation easier, remove the entire front
including the doors. See section: Service.
3. Place the wooden pallet and the cardboard packaging on the
floor and lay the fireplace carefully down on its back.
12
4. Assemble the 3 legs (A) with the adjustable joints (C) with
the aid of 3 screws and washers, which are in the plastic
bag. Attach the joints to the product with the aid of 3
countersunk screws (B) M6x25mm and washers. These are
already attached to the base of the fireplace. Adjust he legs
so that the required height is achieved.
5. Assemble the base heat shield (E) under the base of the
fireplace by using 1 nut M6 and washer.
6. Lift the combustion chamber up.
7. NB! The product is heavy. You will need help during assembly
and when the product is being placed into position.
8. The final adjustments to the legs should only be made after
the insert has had a trial assembly. The bracket (D) should
be placed under the screw heads, both to protect the surface
and to prevent the insert from slipping out of place. The final
adjustment is done with the aid of M10x45mm screws which
are attached to the joints.
9. Replace the parts you removed in order to make the handling
of the fireplace easier.
Ash lip
Place the ash lip next to the bottom frame.
Assembly of the flue connecting pipe (fig. 4)
• The flue connecting pipe (A), which is packed in the box, is
placed on the top of the fireplace.
• Place one clamp iron (B) on each side. These are held in place
with a screw (C) M8x30mm and with nuts.

4.7 Set up/installation

Assembly of the chimney
• First, have a trial assembly of the insert, without making holes
in the chimney. See the measurements of the fireproof wall
in figure 1.
• The insert may be assembled with an Ø 200 mm flue pipe.
• Place the insert into its final position. With the aid of a furnace
cement (or possibly some rope seal), the flue pipe is placed
in the insert's smoke outlet.
• NB! It is important that the joints are tightly sealed. False air
or the like can impair the function of the fire.
4.8 Checking the operating parts (fig. 5)
When the insert is in place, always check the control equipment.
These should be freely mobile and appear satisfactory. The loose
handle can be used when the fireplace is hot.
Top draught (A)
Left position = closed.
Right position = fully open.
Door locks (Classic/Harmony) (B)
Place the handle in the groove on the right hand door and turn
it upwards. Open and close the left door in the same way.
Door lock (Panorama) (C)
Damper (D)
Damper is accessory - (if equipped)
Pushed in = open.
Pulled out = closed.