Publicité
Les langues disponibles
Les langues disponibles
8. CLEANING THE APPLIANCE
Important!
•
Do not use solvents, abrasive detergents or alcohol to clean
the coffee machine.
•
Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
•
Should the machine remain idle for more than a week, it
is advisable to carry out a rinse cycle before preparing any
beverages.
Danger!
•
Never immerse the coffee maker in water when cleaning: it
is an electrical appliance.
•
Before commencing any cleaning operation on the outside
of the machine, turn it off, unplug it from the mains socket
and wait for it to cool down.
✕
✓
✕
✕
✕
✕
8.1 Cleaning the coffee outlet
When
light comes on (orange) (B13), it means that the
coffee circuit needs to be cleaned. This requires special cleaning
tabs for coffee makers, which must be purchased separately. For
more information, visit www.Delonghi.com.
1. Insert the 1-cup filter (C2) in the holder (C1) (fig. 25).
2. Position the cleaning accessory in the filter (C8) (fig. 25)
and press home.
3. Place the cleaning tab on the accessory (fig. 26).
4. Attach the filter holder to the coffee outlet (A18).
5. Fill the tank(A14) with water. Make sure the drip tray (A10)
is empty.
✕
✓
✓
✕
✕
✓
✕
✕
✓
✕
✕
✓
✕
✓
✓
✕
✕
✓
6. Press and hold the
(B13) comes on. After a few minutes, the cleaning cycle
stops automatically.
7. Remove the filter holder and the cleaning accessory.
8. Wash the filter holder and the filter under running water.
9. Attach the filter holder again and run a rinse cycle by press-
ing the
under the filter holder.
10. Remove and empty the drip tray.
Please note:
This cleaning cycle can be initiated at any time by pressing the
button and holding for a few seconds. To cancel, press and
hold the button for at least 10 seconds.
8.2 Cleaning the beans container housing
1. Make sure the beans container (A2) is empty. If in doubt,
operate the mill briefly to make certain.
2. Release the container by turning it anticlockwise and de-
tach it from the machine (fig. 27).
3. Remove coffee residues using a vacuum cleaner (fig. 28).
✕
4. Clean the beans container housing with a moist cloth, and
wipe dry (fig. 29);
5. Reposition the beans container in the coffee mill. The con-
tainer is correctly in place when the arrow ▲ is aligned with
✓
the
symbol and a "click" is heard (fig.30).
8.3 Cleaning the burrs
✓
When cleaning the beans container (A2), clean the container hous-
ing and the top burr with a moist cloth. If the burrs need to be
removed and replaced, contact a service centre.
✓
The burr can be removed in the event of the coffee mill being
jammed by the presence of foreign matter. Should this occur,
remove the beans container and proceed as follows:
✕
1. Attach the filter holder (C1) and operate the mill briefly
without beans to free the internal duct.
2. Turn the appliance off.
3. Turn the grinding adjustment dial anticlockwise as far as it
✓
will go, which is the "REMOVE" position (fig. 31).
4. Gripping the top burr by the handle, pull it up and out of
the housing (fig.32).
5. Clean the burr with a brush (fig. 33) and remove coffee res-
idues using a vacuum cleaner (fig. 28).
23
button (B6) until the light
button: it is advisable to place a container
Publicité
