RIB NO TOUCH 868 Manuel page 32

G
B
to improve the radio signal (for example when MASTER NO TOUCH 868 is installed in a metal
container), connect the 868.3 MHz antenna (code ACG5451) to the J3 terminal, respecting
the connection of the central and ground wire, and position it in a way that is 'in sight' by all
safety devices.
To make the system work properly, it is necessary that between the MASTER NO TOUCH
868 and the safety devices, there are not any obstacles such as concrete walls, iron
surfaces etc. which could interfere with radio signals.
WARNING STATUS (alert to change batteries)
The warning status (WARNING) alerts the user that it is imminently necessary to change
batteries.
When the batteries of NO TOUCH 868 are low and reach 3,1V, NO TOUCH 868 receiver sends a
signal via radio to MASTER NO TOUCH 868 that the batteries are nearly dead.
MASTER NO TOUCH 868 will activate the BUZZER with a tone every 3 s for a duration of 1 minutes
every time you give a command to the automation.
The bi-colour LED DL1 on MASTER NO TOUCH 868 will turn on fixed red.
During these status signals the system is still operating, but it is advisable to change the
batteries as soon as possible in order to avoid the door to stop operating, which happens when
the battery reaches 2,8 V.
ALARM STATUS (battery completely dead or failure)
The alarm status is active when the batteries are completely dead (2,8V) or in the event of
failure.
On the MASTER NO TOUCH 868the LEDs DL3 and DL4 turn off and automation remains stationary
while the LED DL1 flashes red/green (for the entire duration) and the BUZZER emits an alternate
tone for 1 minute.
To stop the alarm you must replace the batteries or repair the failure.
PROCEDURE FOR CANCELLATION OF SAFETY DEVICE/S
To cancel safety device/s stored on MASTER NO TOUCH 868 proceed in the following way:
- Press and keep pressed the PROG. RX pushbutton for 10 s.
- At the end of the 10 s, the LED DL1 flashes 6 times red/green, signalling the cancellation, while
the LEDs DL3 and DL4, if lighted, will turn off.
TECHNICAL CHARACTERISTICS OF MASTER NO TOUCH 868 code ACG6154
- SUPPLY
- VOLTAGE APPLICABLE TO TERMINAL J2
- VOLTAGE APPLICABLE TO TERMINAL J1
- CONSUMPTION AT REST
- MAXIMUM CONSUMPTION
- WORKING TEMPERATURE
- DIMENSIONS
- WEIGHT
TECHNICAL DATA OF RADIO FREQUENCY
- FREQUENCY
- SENSITIVITY
- OUTPUT POWER
- TYPE OF MODULATION
- RANGE
TECHNICAL CHARACTERISTICS OF NO TOUCH 868 PHOTOCELL code ACG8048
NO TOUCH 868 RECEIVER
- SUPPLY
- CONSUMPTION AT REST
- MAXIMUM CONSUMPTION
- TYPE OF MODULATION
- BATTERY LIFE
- WORKING TEMPERATURE
- MAXIMUM TIME ACTIVATION OF THE RECEIVER
- TIME FROM RECOVERY TO RELEASE
- DEGREE OF PROTECTION
- DIMENSIONS
- WEIGHT
TECHNICAL DATA OF RADIO FREQUENCY
- FREQUENCY
- SENSITIVITY
- OUTPUT POWER
- RANGE
NO TOUCH 868 TRANSMITTER
- POWER SUPPLY
- CONSUMPTION
- TYPE OF MODULATION
- BATTERY LIFE
- BATTERY LIFE WITH JP4 IN "L" POSITION Range of the infrared signal 5 m: 3,1 years
- BATTERY LIFE WITH JP4 IN "H" POSITION Range of the infrared signal 10 m: 1,2 years
- WORKING TEMPERATURE
- DEGREE OF PROTECTION
- DIMENSIONS
- WEIGHT
TECHNICAL DATA OF INFRARED SIGNAL
12/24V
- WAVELENGTH
110-240V 50/60Hz
- RANGE
10-30V
30 mA
100 mA
-20 ÷ +60°C
125x55x28 mm
0,090 kg
868.3 MHz
-108 dBm
<25 mW
FSK
20 m in open space
32
1 x LITHIUM AA 3.6V (>2.5 Ah) batteries
5 µA
25 mA
FSK
about 3 years (with 10 daily cycles)
-20 ÷ +60°C
90 ms
90 ms
IP54
Total height with bracket = 190 mm;
width = 34.60 mm;
depth = 32 mm
0,210 kg
868,3 MHz
-108 dBm
<25 mW
20 m in free space without antenna
1 x LITHIO AA 3.6V (>2.5 Ah) batteries)
3 µA
FSK
about 3 years
-20 ÷ +60°C
IP54
Total height with bracket = 190 mm;
Width = 35 mm;
Depth= 51,91 mm
0,210 kg with battery
890 nm
10 m with JP4 in "H" position on TX (by factory - set
to 5 m with JP4 in "L" position)
4
3
2
1
0
5 10
Daily cycles
batteries life
20 30