RIB NO TOUCH 868 Manuel page 25

NO TOUCH 868 complies with the standard EN 13849-1:2015 and, in junction with a RIB control
panel equipped with AUTOTEST, is a PL "c" Category 2 safety system.
The system constantly monitors the presence of the various security devices and battery
status, satisfying the need for fully active security on all types of doors with vertical
movement.
NO TOUCH 868 is a patented device developed to guarantee safety in automations such as
shutters and sectional doors.
The NO TOUCH 868 photocells prevent contact with any obstructions, thanks to their infrared
ray which is 13cm away from the door.
NO TOUCH 868 does not require cable reel systems, because it operates with batteries and
via radio.
The particular system of "balance" allows the control of each movement condition, even when
vibrations are present.
The system is composed of three elements:
1 - 868 MHz radio transceiver, MASTER NO TOUCH 868 (cod. ACG6154) connected to the door
electric control panel.
2 - Aerial 868MHz
3 - Infrared transmitter.
4 - Infrared receiver with 868 MHz radio transceiver which constantly communicates with
the MASTER NO TOUCH 868.
2
3
59
35
Measurements in mm
1
4
35
35
52
25
MASTER NO TOUCH 868 can handle two security devices:
- PHOTOCELL NO TOUCH 868 (code ACG8048). THE NO TOUCH 868 PHOTOCELLS ARE ON ONLY
WHEN THE DOOR IS IN OPERATION. Thanks to the SLEEP MODE function, when the door is
closed, the photocells are turned off, saving the battery life.
- Additional security: RED TRANSMITTER (code ACG6202) connected to NC (not supplied) to
be applied to the pedestrian door on the main door. It will only work if you have already
programmed the NO TOUCH 868 photocell.
THE RED TRANSMITTER IS ALWAYS ACTIVE AND WHEN THE PEDESTRIAN DOOR IS OPENED (and
thus the NC contact to which it is linked is open) LOCKS THE OPERATION OF THE MAIN DOOR.
REFERENCE TO STANDARDS FOR AUTOMATIC VERTICAL DOORS
Once machine installation is complete it must be ascertained that it complies with standard
EN 13241-1.
RIB MAY NOT BE HELD RESPONSIBLE FOR DAMAGES CAUSED BY IMPROPER, WRONG OR UNREASONABLE
USE.
Usage restrictions: The NO TOUCH 868 photocells cannot be used on devices excluded by the
application of the EN 12978, such as:
- protection devices for the installation on doors used for a different purpose to those ones
used for pedestrian or veheicle access, covered by the norm which principal intent is that of
allowing a safe access to industrial, commercial, public and commercial sites. Some examples
of excluded accesses can be: sluice gates, dams, lift doors, vehicles' doors, doors used mainly to
restrain animals, theatre curtains, railways barriers, barriers used only for vehicles.
- Devices used only fo the standard control and for the stopping, including the emergency
stopping, of motorized doors.
- Safety systems and safety devices used on machineries different from doors.
⚠
Any possible modification of the device, or of the configuration of the same cannot be
carried out without the clear authorization by the manufacturer or, by the local authorized
dealer.
The installer of the safety device must make sure that the end user know the following:
- That the safety devices must be made known to all appropriate people.
- That the passages to reach the devices must be kept clear from any obtsacle.
- About the procedures for cleaning so to avoid the dangerous building up of material.
- The possible details for a restart of the system after an emergency or accidental stop caused
by the control system.
Any modification of the project or, of the configuration of the device, without discussing it first
with the manufacturer or with the local autorized dealer can cause dangerous situations.
If two MASTER NO TOUCH 868, installed at a distance of about 20 m from one another,
are commanded simultaneously, their communication and check signals with the
accessories can overlap and interfere with each other, causing the systems to go
into alarm.
⚠
G
B