Peg-Perego b1nrkwwf2bs Notice D'emploi page 16

_ Always apply the brake when loading or unloading
children.
_ WARNING! Do not add any mattress are not approved
by the manufacturer.
_ Do not use accessories which are not approved by the
manufacturer.
COMPONENTS OF THE ITEM
Check the contents of the packaging and if you have
any complaints please contact the Assistance Service.
_ The Book for two pushchair features: a basket, 2 rear
wheels, 2 front wheels, handlebar, front bar, hood, rear
wheel crosspiece
INSTRUCTIONS
1 OPENING: Before opening the frame, remove (without
using blades) any die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE FASTENER BEYOND ITS
LIMIT.
_ DO NOT USE THE FASTENER AS A CARRY HANDLE OR
TO CARRY WEIGHTS.
DO NOT HANG BAGS OR OTHER ACCESSORIES TO THIS
FEATURE.
Press down the side fastener, hold the upper section of
the handle and rotate it towards you until the frame is fully
opened (fig_a). Open frame (fig_b).
The frame is properly opened when the attachment on the
base clicks into place, as shown.
2 FITTING THE WHEELS: Slot the uprights into the rear
wheel crosspiece (fig_a), ensuring that it is facing the
right way, then push the rear wheels on and make sure
that they click into place (fig_b). To mount the front
wheels, fit them into the uprights until they lock into place
(fig_c).
3 ATTACHING THE MAIN HANDLE: if the handle tube
faces upwards, align it with the stroller (Fig_a).
Fasten the handle to the frame as shown in the figure
(Fig_b).
To complete the operation, press the two side buttons
on the handle (Fig_c) to ensure the handle pushes in
all the way, until it clicks into place (Fig_d).
4 FITTING THE BASKET: if lowered, lift the basket tube to the
horizontal position. Press the silver buttons under the metal
basket tube located at the back of the stroller (fig_a) and
remove the metal tube (fig_b). Thread the tube through the
fabric loop on the back of the basket, making sure that the
two silver buttons are facing downward (fig_c). Re-attach
the tube to the housings (fig_d).
5 IMPORTANT! Fasten the three lower basket loops to
the three grey buttons on the rear bar. Note that the
loops open (fig_a)
Secure the two upper basket vinyl eyelets to the two grey
buttons on either side of the metal tube housing.
Note that the loops open (fig_b). Fasten the two Velcro
straps to the sides of the frame (fig_c).
WARNING! If this operation is not completed properly,
the basket will not support any weight.
Fix the front flaps of the basket onto the frame's grey
buttons (fig_d) and slip the central slot onto the frame's
hook (fig_e).
6 HOOD: to apply the hoods, place the attachments in
their seats (matching left and right) until they click.
7 Fasten the Velcro strip on the rear of the backrest
(fig_a), secure the central rubber band (fig_b) and the
side rubber band (fig_c).
8 Button laterally (fig_e) and centrally (fig_f ) the two
buttons to the frame.
9 SWIVEL WHEELS Lower the lever to release the front
wheels (swivel position) (fig_a). Lift the lever to fix the
front wheels (fig_b). The rear wheels are fixed.
10 Press the lever down to apply the brake and lock the
frame. Do the opposite to release the brake (fig_a)
ADJUSTABLE HANDLEBAR: To adjust the height of the
handlebar, press both of the side buttons at the same
time (fig_b) and swing it into the desired position
(fig_c), then release the buttons.
11 FOOTREST: before adjusting the foot rest, ensure its
cover is accurately fitted; if it isn't, fit it accordingly. To
lower the footrest push the two levers downwards and
then push the footrest downwards (fig_a); to raise the
footrest lift it upwards (fig_b).
12 FRONT BAR: to remove the front bar, pull it out to the
second position (fig_a) and remove (fig_b).
Open-close front bar: remove it from one side and
rotate (fig_c).
13 HOOD: The hood comes with a loop for hanging your
child's favorite toy (fig_a) and a see-through window
for observing your child (fig_b), which can be lifted
and fastened. You can detach the Velcro, roll up the
back of the hood and fasten it at the top with the
rubber band to allow greater ventilation during use
with the backrest down (fig_c). The hood may be
pulled forward into several positions (fig_d).
14 ADJUSTING THE BACKREST: to lower the backrest press
the clip (fig_a) and the backrest will move down to the
desired position (fig_b).
To raise the backrest, press the clip and lift the
backrest to the desired height.
15 FIVE POINT SAFETY HARNESS: To fasten it, push the two
waist strap buckles (with the shoulder straps attached
– arrow_a) into the leg divider until they click into place
(arrow_b). To unfasten it, press the round button in the
centre of the buckle (arrow_c) and pull the waist straps
out (arrow_d).
16 To tighten the waist strap, pull on both sides in the
direction of the arrow (arrow_a). To loosen it, move it
in the opposite direction.
17 Before adjusting the height of the safety harness
remove the shoulder pads (fig_a). To adjust the height,
slip the belts through the eyelet in the fabric (fig_b)
and position them in the most suitable eyelet.
18 FOLDING UP To fold up the stroller you must ensure the
front wheels are fixed and the hood are closed, when
fastened. Place the handle as shown in the figure (fig_a).
Pull the inside handle on the base (fig_b) and lift it (fig_c);
the handle will drop forward until the frame is closed.
19 To close correctly, check the side hook is inserted
(fig_a). If not automatically locked, compress the
chassis slightly. When folded, the stroller will free
standing (fig_b).
20 For greater compactness, it is possible to remove the
wheels.
To remove the rear wheels: pull the pivot outwards and
remove the wheel as shown in the figure (fig_a).
To remove the front wheels: press the tab as shown and
remove the wheel (fig_b).
TRANSPORT: the stroller can be carried comfortably
locking the front wheels and grasping the main handle
(fig_c).
21 REMOVABLE ITEMS: to remove the hood, take the
central and outer elastic off from the attachments
under the handlebar (fig_a), unbutton the side and
central buttons from the frame (fig_b), remove the
Velcro strips from the backrest (fig_c) and remove the
hood attachments from their position on the frame,
pressing on the inner tabs (fig_d).
22 To remove the soft cover, press in the holes on the
inside of the frame (fig_a); remove, from the side ofthe
seat, the rigid flap of the soft cover (fig_b),unbutton the
four buttons under the handlebar (fig_c) and unfasten
the elastics under the seats (fig_d). Detach the two
central buttons and the two side buttons visible from
under the soft cover (fig_e).
23 From the front, remove the soft cover from the footrest
(fig_a), remove the leg divider strap fromunder the seat
(fig_b), and remove the backrest from the frame (fig_c).
24 Remove the soft cover from the frame (fig_d), remove
the safety belts (fig_e), unscrew the two screws from
the safety belts using a screwdriver (fig_f ) and then
remove the backrest (fig_g). Do the opposite to replace
the soft cover.
- 16 -