Sovelor GA100C Manuel D'utilisation Et De Maintenance page 10

• The generator is placed near a power switchboard having
specifications that conform to those declared;
• The unit is placed in a fixed position
• The hot air jet is directed towards the cylinder.
• The heater is regularly monitored during operation and
checked before being started up;
• At the beginning of each working period, before plugging it
into the electrical power supply, a check is made that the
fan moves freely;
• At the end of each working period the main switch is
disengaged and the gas stopcock is closed.
Warning
This unit may not be used by persons (including
children) with reduced physical, sensorial or
mental capacities or with limited experience and
familiarity unless they are under supervision or
instructed on how to use the equipment by the
person responsible for its safety.
INSTALLATION INSTRUCTIONS
Warning
All the operations described in this section must
only be performed by professional and skilled
personnel.
POWER CONNECTIONS
Warning
The power line of the generator must be fitted with
an earth lead and a residual current circuit breaker.
The supply cable must be connected to a
switchboard that has an isolation switch.
All the control and safety devices are already electrically
connected.
Before switching on the heater, and therefore, before plugging
it into the electrical power supply, a check must be made that the
power supply specifications are the same as those stated on the
identification plate.
Warning
The equipment is fitted with a temporary power
cable, used for the working test.
The temporary power cable must be removed and
replaced with a H07RN-F cable having a 1.5 mm2
diameter. The cable must be stripped leaving the
earth conductor at least 2 cm longer.
The electrical power cable must be connected in conformity to
the polarity specified on the main terminal board of the electrical
panel: phase (L) and neutral (N).
Warning
If polarities L and N are incorrect, the space heater
may stop a few seconds after it is switched on for
the first time.
If any room thermostat or other accessories are connected to
the system (such as the timer for example) this must be done by
connecting the electrical cable to the thermostat plug (10):
EN
• Take the plug (10) out of the power switchboard, open it and
remove the electrical jumper between terminals 2 and 3 of
the plug.
• Connect the thermostat electrical cable to terminals 2 and 3
of the thermostat plug (10)
• Close the plug again and plug it back into the power
switchboard
Warning
Never attempt to switch the heater on or off by
connecting the room thermostat (or other control
devices) to the electrical power line.
Installation and connection of all the other accessories are
given in the specific instructions enclosed with each accessory,
like the specific user instructions.
The electrical diagram in this manual indicates only the
electrical connection of the accessory to the existing electrical
system of the heater.
CONNECTION TO GAS CYLINDER
The heater must be connected to an appropriately sized gas
cylinder. A gas supply stopcock must be installed between the
heater and the cylinder
Warning
All of the connections have left-hand threads, and
must therefore
anticlockwise.
Warning
The dimensions of the gas cylinder must be based
on the required gas flow rate and supply pressure.
The supply pressure to the pressure regulator
must always be greater than 2 bar
The heater is supplied complete with gas hose (a) and
pressure reducer (c) with fittings (d) for connection to different
types of cylinders.
Depending on the country of destination, the heater may be
supplied with three different types of gas pressure regulator.
TYPE I
• pressure regulator with G5 fitting for AT-BG-CY-DA-DE-EE-
LT-LV-MK-MT-RO-TR.
• G5/G2 fitting, with G2 fitting for G2 for BE-CZ-ES-FR-HR-
HU-LU-PL-PT-SI-SK.
• G5/G1 fitting, with G1 fitting for IT-GR
• seal for NL, to install on G5 pressure regulator
Warning
The installer is responsible for guaranteeing that
the correct fitting is used for the connection to the
gas cylinder.
21
be tightened by turning